GTAC-Sam Publish time 2022-3-2 11:39:39

How to configure trunk port on Ruijie device?

This example shows how to prune a trunk port to carry traffic only for vlan 5, 10 and 20-30Ruijie#configure terminalRuijie(config)#interface gigabitEthernet 0/1Ruijie(config-if-GigabitEthernet0/1)#switchport mode trunkRuijie(config-if-GigabitEthernet0/1)#switchport trunk allowed vlan remove 1-4,6-9,11-19,31-4094Ruijie(config-if-GigabitEthernet 0/1)#endRuijie#wr

soporte@wifiemp Publish time 2022-9-2 05:17:55

Hi there. I'm trying to configure a trunk port in a Ruijie AP180 in the GigabitEthernet 0/1 port. This is my configuration as follows:



interface GigabitEthernet 0/1
encapsulation dot1Q 1
ip dhcp snooping trust

interface GigabitEthernet 0/1.23
encapsulation dot1Q 23
ip dhcp snooping trust

interface GigabitEthernet 0/1.27
encapsulation dot1Q 27
ip dhcp snooping trust

interface GigabitEthernet 0/2
encapsulation dot1Q 23

interface GigabitEthernet 0/3
encapsulation dot1Q 27

However It doesn´t work as it should be neither the Gigabit 0/2 or 0/3 are working, I followed some tutorials from community. Any advide? Im using the lastest firmware


yujiamin@ruijie Publish time 2022-9-2 15:31:41

ReinierBallester replied at 2022-9-2 05:17
Hi there. I'm trying to configure a trunk port in a Ruijie AP180 in the GigabitEthernet 0/1 port. Th ...

Dear sir

May I know how you test that it cannot work? Does the vlan23 and vlan27 can go through the g0/1 successfully?


Best regards
Jenny

soporte@wifiemp Publish time 2022-9-6 10:48:36

GTAC-Jenny replied at 2022-9-2 15:31
Dear sir

May I know how you test that it cannot work? Does the vlan23 and vlan27 can go through t ...

Hi there, I resolved that in this way:
I put the Cisco port switch in trunk mode witch native vlan 23 an passing aditional the vlan 27.
In the AP the default native vlan is 1 so work in all interfaces as "23". So I deleted the 23 and just pass the 27 and put in the the second port the 27 and work as it should.
Thank you

daniel.capina@n Publish time 2024-3-15 15:54:17

Edited by Dan Capina at 2024-3-15 15:56

ReinierBallester replied at 2022-9-6 10:48Hi there, I resolved that in this way:I put the Cisco port switch in trunk mode witch native vlan ...data/attachment/forum/202403/15/155150g3j8z18jw282bccv.pngAP840-I version AP_RGOS 11.9(6)W1B1, Release(09173122)How do I configure the trunk thru CLI or WEB?

yangyue1@ruijie Publish time 2024-3-15 16:05:22

Dan Capina replied at 2024-3-15 15:54
ReinierBallester replied at 2022-9-6 10:48Hi there, I resolved that in this way:I put the Cisco po ...

Hello sir, trunk or access is switch concept, you cannot cobfigure it on AP
Pages: [1]
View full version: How to configure trunk port on Ruijie device?