How to configure load balance on Ruijie/Reyee EG?
Click How to Setup WAN Load Balance on Reyee EG to configure load balance on Reyee EG.Here are the detailed configure steps to configureload balance on Ruijie EG:
Introduction of WAN Load Balance
The load balancing function distributes the data to multiple WAN interfaces to avoid the traffic congestion and provide redundancy.
Case of configuration
a) Network Topology
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/ce292c4bf6c44f56995e6612d7f381c6.png
b) Configuration Key Point
1) Configure IP address of the WAN ports and default routes.
2) Enable the load balancing policy.
3) Customize interface weight to ensure that traffic goes through the different egress according to weight.
C) Configuraiton Steps1) Configure WAN 0
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/a257c18e338e46cb90926cbf19d265cb.pnghttps://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/f3ec15b6ce2a4fa5811e9127a2bb099b.png
2) Change the LAN1 port to WAN port
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/739300fb352640889de01d83d09a67fb.png
3) Configure WAN 1
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/5b65b6ca169b432c9c8ab7c34b4a26e5.png
4) Enable Load Balance
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/0ea4437c6b044146926e6613dfb110ee.png
5) Configure the interface weight for two link
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/85296decffaa4fa8967af68d1d7b7b1c.png
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/e7dd8ab0ba0c435e9d17d8caf46f371d.png
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/467c3cb078c74de99f0a4270247fbd1b.png
Configuration Verfication
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/3eada4a1e46a43a5bc7c0c537cbaeae1.pnghttps://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/62c322d614704c73a341b1f40bc7ce7b.png
Advice to add the following configuration to convert to reachable link when one of link can't be reached
https://img.sobot.com/console/eee7ec2e351e4569a4791536fb5f0973/kb/image/990217c8d40e4468beff56725496bd18.png
IP address： The IP need to be reached
Next Hop IP: The gateway IP of yourWAN port IP
is this the same as configuration in NBR series and EG Series?
NosSon replied at 2024-4-30 10:06
is this the same as configuration in NBR series and EG Series?
Dear sir
Yes, this is same configuration guide for NBR and Ruijie EG
However, different versions of the interface may be different
you can also refer to the WAN load balancing configuration via this link for NBR:
https://reyee.ruijie.com/en-global/resources/preview/reyee-rg-nbr-series-routers-web-based-configuration-guide
data/attachment/forum/202404/30/101904g7x4g42xn29xlizi.png
Best regards,
Ross
GTAC-Ross replied at 2024-4-30 10:19
Dear sir
Yes, this is same configuration guide for NBR and Ruijie EG
Thank you for your response.
how about the Failover?
Pages:
[1]