Forum › Wireless › When the wireless user speed limit fails, what should be done to check?

GTAC-Sophia Publish time 2023-7-25 11:49:52

When the wireless user speed limit fails, what should be done to check?

data/attachment/forum/202307/25/114435renvtnkttetttdvv.png

Check rate limitation configuration enabled by different devices
1. Rate limitation on Ruijie EG
(1) Check whether IP range is correct
data/attachment/forum/202307/25/114509wo2m2x9zgk622g7o.png

2. Check If user enables Flow Control

data/attachment/forum/202307/25/114531igt1uhy8f99wuefp.png

3. If the user chooses the corresponding user group

data/attachment/forum/202307/25/114547iw6qofsoofw7cspf.png

data/attachment/forum/202307/25/114557xow5w4dzns36v4wv.png

4. Check whether users add the policy successfully

data/attachment/forum/202307/25/114616h5hv051kqknn9qrs.png

data/attachment/forum/202307/25/114627qy4v73c4dxcpx461.png
2. Rate limitation on Ruijie AP

AP-based rate limit:
Format: Fat AP(config)#wlan-qosap-based {per-user-limit | total-user-limit } {down-streams | up-streams}average-data-rate average-data-rate brust-data-rate brust-data-rate
FatAP(config)#wlan-qosap-based per-user-limit down-streams average-data-rate 800 burst-data-rate 1600

Wlan-based rate limit:
Format: Fat AP(config)#wlan-qoswlan-based {wlan-id | ssid} {per-user-limit | total-user-limit} {down-streams |up-streams} average-data-rate average-data-rate brust-data-rate brust-data-rate
FatAP(config)#wlan-qoswlan-based 1 per-user-limit down-streams average-data-rate 800 burst-data-rate 1600

Mac-based rate limit:
Format: Fat AP(config)#wlan-qosnetuser mac-address {inbound | outbound} average-data-rate average-data-rate burst-data-rate burst-data-rate
FatAP(config)#wlan-qosnetuser 0001.0001.0001 inbound average-data-rate 800 burst-data-rate 1600

Note: Check the commands are delivered successfully
Ruijie#show run---->check if the corresponding commands are taking effect？
data/attachment/forum/202307/25/114831v9z9srdll59dqn9d.png

data/attachment/forum/202307/25/114839iwozqq8d4qwfwzi8.png
3. Rate limitation on AC
Check the commands are delivered successfully.
AP-based rate limit:
Ruijie(config)#ap-configRJAP
Ruijie(config-ap)#ap-basedper-user-l
imitdown-streams average-data-rate 800 burst-data-rate 1600

Wlan-based rate limit:
AC(config)#wlan-config1 RL
AC(config-wlan)#wlan-basedper-user-limit down-streams average-data-rate 800 burst-data-rate 1600

Mac-based rate limit:
AC(config)#ac-controller
AC(config-ac)#netusermac-address   { inbound | outbound }average-
data-rateaverage-data-rate burst-data-rate burst-data-rate

AC#show dot11 ratelimit wlan
AC#show dot11 ratelimit user
AC#show dot11 ratelimit ap
4. Rate limitation on Reyee EG
rate limiationon Reyee EG

View full version: When the wireless user speed limit fails, what should be done to check?