Ruijie Community

Title: AnyLink - HQ [Print this page]
Author: masmith22@veriz    Time: 2025-2-14 13:23
Title: AnyLink - HQ
Is it possible to broadcast the HQ WiFi SSID in the branch office?
Can you assign a server with a HQ static IP address located in the branch office?
Thanks,
Alonzo
Author: guominxiang@rui    Time: 2025-2-14 15:57
Hello,

1. Can you tell me which VPN type did you configure? Is SD-WAN?
2. What is your device model?
3. Can I know what is server address? Will it changes dynamic then you need fix a static ip?

Best regards,
Micca
Author: masmith22@veriz    Time: 2025-2-16 02:00
GTAC-Micca replied at 2025-2-14 15:57
Hello,

1. Can you tell me which VPN type did you configure? Is SD-WAN?

Hello,
1. Can you tell me which VPN type did you configure? Is SD-WAN? I have configure SD-WAN.
From the HQ, I am able to RDP to the servers in the branch office. I would to assign a static IP from the HQ subnet.
Can you broadcast HQ SSID in a branch office.?
2. What is your device model? HQ Model:EG305GH-P-E  Branch Model:EG1510XS
3. Can I know what is server address? 192.168.12.X
4. Will it changes dynamic then you need fix a static ip? the servers on the branch have a static


Author: v-songruiqi@rui    Time: 2025-2-16 13:19
Mario replied at 2025-2-16 02:00
Hello,
1. Can you tell me which VPN type did you configure? Is SD-WAN? I have configure SD-WAN.
Fr ...

Hi, do you mean sssign the static IP of the HQ subnet to the branches, so that the HQ can access the branch servers through RDP?
Author: masmith22@veriz    Time: 2025-2-17 10:09
GTAC-Rachel replied at 2025-2-16 13:19
Hi, do you mean sssign the static IP of the HQ subnet to the branches, so that the HQ can access th ...

I currently use OPNvpn and Wireguard vpn to access the HQ. I need to be on the HQ network to access the servers. I would like to use SD-WAN, if possible. Use VPN only when I am working remote.


Is their SD-WAN solution based on Wireguard?
Does the router have to have a public IP for this to work?
Are they also going to build zero trust type networking into this?
Author: v-shaojinren@ru    Time: 2025-2-17 17:03
Mario replied at 2025-2-17 10:09
I currently use OPNvpn and Wireguard vpn to access the HQ. I need to be on the HQ network to acces ...

Dear customer,
The router does not necessarily need a public IP to establish the connection in our SD-WAN solution.
The success of the connection depends heavily on the NAT type of your network.


There are two methods for communication between two branches. One is direct device-to-device communication, referred to as the P2P direct connection method. The other is message relay via a supernode, referred to as the forwarding mode.
When neither branch has a public IP address (e.g., most residential broadband services lack public IPs), NAT traversal will be attempted. If NAT traversal succeeds, P2P communication can be established between the branches. Otherwise, communication must rely on supernode forwarding.
When does NAT traversal fail?
Currently, there are four types of NAT: full cone, restricted cone, port-restricted cone, and symmetric NAT. Due to the characteristics of NAT types, there are three combination scenarios where NAT traversal is theoretically impossible:
How to determine the type of NAT?
The NAT type is related to the outbound ISP, region, and link mode.
Author: masmith22@veriz    Time: 2025-2-19 13:20
GTAC-Ryan replied at 2025-2-17 17:03
Dear customer,
The router does not necessarily need a public IP to establish the connection in ou ...

The AnyLink is configured and working. Can you expand a HQ SSID to the branch? Can an employee travel between HQ and Branch seamless connecting the corp wifi?
Author: guominxiang@rui    Time: 2025-2-19 13:28
Mario replied at 2025-2-19 13:20
The AnyLink is configured and working. Can you expand a HQ SSID to the branch? Can an employee tra ...

Hello,

This feature is not currently supported. If you need, I can try to feedback to R&D team.

Best regards,
Micca




Welcome to Ruijie Community (https://community.ruijienetworks.com/) Powered by Discuz! X3.2