Ruijie Community

Title: [Trouble shooting case]POE can’t power for PD devices [Print this page]

Author: Jason Time: 2020-8-26 11:15
Title: [Trouble shooting case]POE can’t power for PD devices

Step1: Switch are managed switch or UnmanagedSwitch

S1800 series and ES100 seriesswitch are unmanaged switches

Reyee-switch can’t use commandto check either

Step2: Replace cable and interface

After replacing cable can work well

---cable issue

After replace interface or switch can workwell,

---unmanaged switch hardware issue

---Reyee managed switch, checking web configuration，if POE enable normally but can’t POE out,hardware issue.

---RGOS switch keep checking

Step3：Collectthe POE interfaces status and check whether the powersupply are enough

Using the following commands to collectinformation:

show poe interfacesstatus

show poe powersupply

show log

Using the following commands to solve issue

Ruijie(config)#poe legacy

Ruijie(config)# poe modeenergy-saving // need to power off restartthe switch or can’t work

Forexample

Problem1: All POE interfaces status are off, but power overload

[attach]475[/attach]

[attach]474[/attach][attach]474[/attach]

[attach]473[/attach]

Reason: may POE chip over voltage

Solution：Try with the following commands, if still can’t, hardware issue

Ruijie(config)#poe legacy

Ruijie(config)# poe mode energy-saving // need to power off restart the switch orcan’t work

Problem2: POE interface power for PD unstable

Reason: low port voltage

Solution：Try with the following commands, if still can’t, hardware issue

Ruijie(config)#poe legacy

Ruijie(config)# poe mode energy-saving // need to power off restart the switch orcan’t work

Problem3: XS-S1960-10GT2SFP-P-H only can power for 5 devices

[attach]479[/attach]

[attach]478[/attach]

Reason: the PSE total remain power isn’t enough,cause there are three class 4 POE+ port.

Solution: if the PD devices only need POE,change the Power management mode to be energy-saving mode. If need POE+, needto add POE switch or change one.

Ruijie(config)# poe mode energy-saving // need to power off restart the switch orcan’t work

Step4: After enable legacy, if the POE are working, using the following guide toupgrade MCU to solve this issue thoroughly.

MCU file:https://pan.ruijie.com.cn/share/ad4be55f91f59512694abaec5a

And if the current switch version lower than B12P11 version, pleaseupgrade to B12P11 or later version

Thestep:

1. show poe powersupply

2. set switch and PC same network,like 192.168.1.1 192.168.1.2

3. put tftp server and MCU on samefolder

4. copy MCU to switch

Ruijie#copytftp://192.168.1.1/22021413_0806_005.s19 tmp:

PressCtrl+C to quit

Copysuccess.

Ruijie#

5.upgrade MCU

Ruijie#upgradepoe tmp:22021413_0806_005.s19

Ruijie#*Dec11 18:02:49: %POE-4-UPGRADE: PoE mcu is upgrading, don't power off the device,please wait...

*Dec11 18:02:49: %POE-4-UPGRADE: *******************0%*******************

*Dec11 18:03:45: %POE-4-UPGRADE: *******************10%*******************

*Dec11 18:04:43: %POE-4-UPGRADE: *******************20%*******************

*Dec11 18:05:41: %POE-4-UPGRADE: *******************30%*******************

*Dec11 18:06:39: %POE-4-UPGRADE: *******************40%*******************

*Dec11 18:07:37: %POE-4-UPGRADE: *******************50%*******************

*Dec11 18:08:35: %POE-4-UPGRADE: *******************60%*******************

*Dec11 18:09:33: %POE-4-UPGRADE: *******************70%*******************

*Dec11 18:10:31: %POE-4-UPGRADE: *******************80%*******************

*Dec11 18:11:29: %POE-4-UPGRADE: *******************90%*******************

*Dec11 18:12:06: %POE-4-UPGRADE: *******************100%*******************

*Dec11 18:12:06: %POE-4-UPGRADE: PoE mcu upgrade success, version:214.

*Dec11 18:12:06: %POE-4-UPGRADE: Please power off the device and startagain.

6. reloadswitch

Ruijie#reload

Reloadsystem?(Y/N)y

7. checkwhether the MCU upgrade successfully

Ruijie#showpoe powersupply

Devicemember : 1

Mcusoftwareversion : 214

Powermanagement : energy-saving

PSEtotalpower : 125.0 W

PSEtotal power consumption : 0.0 W

PSEtotal remain power :125.0 W

PSEpeakpower : 0.0 W

PSEaveragepower : 0.0 W

PSEpoweredport : 0

PSEwarningpower : 90

PSEclasslldp : enable

PSEuninterruptible-power :disable

Globallegacy : off

5.png (24.2 KB, Downloads: 355)

Author: admin Time: 2021-5-19 17:52
Very good sharing

Welcome to Ruijie Community (https://community.ruijienetworks.com/)