Title: What should i do if device offline on Ruijie Cloud? [Print this page] Author: GTAC-Daisy Time: 2021-12-2 11:45 Title: What should i do if device offline on Ruijie Cloud? 1. Check Network Connectivity
1) Verify the connectivity between Ruijie device and Ruijie Cloud.
ping devicereg.ruijienetworks.com on device CLI.
2) Whether your device's IP address, gateway, DNS server are configured
Ruijie(config)#int bvi 1
Ruijie(config-if)#ip address 192.168.1.1 255.255.255.0 //configure IP
Ruijie(config-if)#end
Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.254 //configure gateway
Ruijie(config)#ip name-server 8.8.8.8 //configure DNS
3) Following ports are used for Ruijie Cloud management. Ensure these ports are available and the data stream is permitted.
Note: AP and SMB switch have default CWMP setting which allows devices can look for Ruijie Cloud automatically. But for enterprise switch(RG-S29 series), It needs to configure CWMP URL on CLI manually.
Ruijie#configure ter
Ruijie(config)#cwmp
Ruijie(config-cwmp)#acs url http://devicereg.ruijienetworks.com/service/tr069servlet
Ruijie(config-cwmp)#end
Ruijie#wr
2. Check Device Running Mode(Wireless only)
Verify whether the AP is running in FAT mode, if the device is working in FAT mode, it needs to switch AP into macc mode on WEB or CLI for Ruijie Cloud registration. the command are following
Ruijie#ap-mode macc
Note: By default, AP is running in FIT Mode and will convert MACC mode automatically once it has Internet access.
3. Check Ruijie Cloud Hosting(Asia or Europe)
1) In order to provide smooth access and reduce Internet latency for users in Ruijie Cloud solution. There is 2 Ruijie Cloud hosting installed for global service. The dynamic hosting selection for regions or countries shows as below:
2) As 2 hosting databases are isolated, if the serial number you input on and the device DNS resolution is not the same hosting, the device will not show online. First, verify which hosting you are accessing in the browser. Simply login your Ruijie Cloud account, and check the URL link.Cloud-as represents Asia cloud and cloud-eu is Europe Cloud. Then, login device's cli and execute ping cloud.ruijienetworks.com and check which IP address is resolved.(Please check the table above for the information). Please confirm the cloud hosting you are accessing is the same as the one device registered.
4. Check Device Firmware
Whether the device is running the latest firmware as Ruijie Cloud recommended, if the firmware version is too old, it may not be compatible with Ruijie Cloud. User can log in device's web or cli and upgrade to latest firmware version. Please refer Ruijie Cloud Supported Model and Recommended Firmware Version: https://cloud-as.ruijienetworks.com/design/#/home?activeKey=1
5. Check Serial Number
Whether the device's serial number is matched with the one displayed on Ruijie Cloud. The serial number can be found on device back panel or exec "show version" on CLI.
6. Check CWMP configuration
The following is right cwmp configuration:
show cwmp configuration
CWMP status : enable
ACS URL: http://devicereg.ruijienetworks.com/service/tr069servlet (DYNAMIC)
CPE URL: http://172.29.60.63:7547/ (DYNAMIC)
If the configuration is wrong, you can use the command following to change.
AP#config ter
AP(config)#cwmp
AP(config-cwmp)#acs url http://devicereg.ruijienetworks.com/service/tr069servlet ----you can replace 'devicereg' to 'cwmpsvr-as' or 'cwmpsvr-eu' base on the cloud you are using.
AP(config-cwmp)#end
AP#wr
Welcome to Ruijie Community (https://community.ruijienetworks.com/)
