How to configure WDS for fat ap in point-to-point structure? - Ruijie Community

Since wireless devices are connected to each other, this structure is suitable for a network connecting two fixed points. The network topology is shown below:

The wired interface of the root bridge is connected to the wired network, and its wireless interface is connected to the non-root bridge; The wireless interface of the non-root bridge is connected to the root bridge, and its wired interface is connected to the wired network; Two separate wired networks are connected in a wireless manner through the wireless bridging between the root bridge and the non-root bridge.

2) FAT AP can support 2 bridging ways, mac-address and ssid.The following configuration will take mac-address bridging for example.

3) In AP630 B8 version or later, it can support WDS encryption, but only RSN's and WPA's AES encryption.It doesn't support Tkip encryption.

4) If the distance of wireless transmission in WDS is over 1000m, you need to add a command:

interface Dot11radio 2/0
peer-distance 4000 //actual distance is 2000m
Please set the distance to a larger value (2-3 timesthe actual distance)

AP-1(config)#vlan 10
AP-1(config-vlan)#exit

AP-1(config)#dot11 wlan 1
AP-1(dot11-wlan-config)#ssid ruijie-test

AP-1(config)#interface dot11radio 2/0
AP-1(config-if-Dot11radio 2/0)#encapsulation dot1Q 10 //encapsulation vlan
AP-1(config-if-Dot11radio 2/0)#radio-type 802.11a //set radio 5.8G
AP-1(config-if-Dot11radio 2/0)#channel 149 //setchannel 149
AP-1(config-if-Dot11radio 2/0)#chan-width 40
AP-1(config-if-Dot11radio 2/0)#station-role root-bridge bridge-wlan 1 //set ap as root-ap
AP-1(config-if-Dot11radio 2/0)#wlan-id 1 //SSID mapping

AP-1(config)#interface bvi 10
AP-1(config-if-BVI 10)#ip address 192.168.1.1 255.255.255.0

AP-1(config)#interface gigabitEthernet 0/1
AP-1(config-if-GigabitEthernet 0/1)#encapsulation dot1Q 10

AP-1(config)#data-plane wireless-broadcast enable

AP-1(config)#dot1 wlan 2 //create WLAN
AP-1(dot11-wlan-config)#ssid ruijie-wds-test //create ssid
AP-1(dot11-wlan-config)#exit
AP-1(config)#vlan20 //crea tVlan
AP-1(config-vlan)#exit
AP-1(config)#int dot11radio 1/0.1
AP-1(config-subif-Dot11radio 1/0.1)#encapsulation dot1Q 20 //configure radio interface encapsulation vlan
AP-1(config-subif-Dot11radio 1/0.1)#exit
AP-1(config)#int dot11radio 1/0
AP-1(config-if-Dot11radio 1/0)#wlan-id 2

AP-2(config)#vlan 10
AP-2(config-vlan)#exit

AP-2(config)#interface dot11radio 2/0
AP-2(config-if-Dot11radio 2/0)#encapsulation dot1 Q10    //encapsulation vlan
AP-2(config-if-Dot11radio 2/0)#station-role non-root-bridge    //set AP role as non-root bridge
AP-2(config-if-Dot11radio 2/0)#parent mac-address 061a.a97f.1114    //set BSSID,and you can use "parent ssid xxxx" to match the SSID

AP-2(config)#interface bvI 10
AP-2(config-if-BVI 10)#ip address 192.168.1.1 255.255.255.0

AP-2(config)#data-plane wireless-broadcast enable

AP-1(config)#dot1 wlan 2 //create WLAN
AP-1(dot11-wlan-config)#ssid ruijie-wds-test //createssid
AP-1(dot11-wlan-config)#exit
AP-1(config)#vlan20 //creat Vlan
AP-1(config-vlan)#exit
AP-1(config)#int dot11radio 1/0.1
AP-1(config-subif-Dot11radio 1/0.1)#encapsulation dot1Q 20 //configure radio interface encapsulation vlan
AP-1(config-subif-Dot11radio 1/0.1)#exit
AP-1(config)#int dot11radio 1/0
AP-1(config-if-Dot11radio 1/0)#wlan-id 2

AP-1#show dot1 associations all-client
RADIO-ID WLAN-IDADDRAID CHAN RATE_DOWN RATE_UP RSSI ASSOC_TIME IDLE TXSEQ RXSEQ ERP STATE CAPS HTCAPS
2100:14:4b:6f:b8:361149 144.5M144.5M600:00:32 15565535 0x00x3 Es S

AP-1#ping 192.168.1.2
Sending 5, 100-byte ICMP Echoes to 192.168.1.10,timeout is 2 seconds:
< press Ctrl+C to break >
!!!!!
Success rate is 100 percent (5/5), round-tripmin/avg/max = 2/11/28 ms.

Ruijie#show dot11 wds-bridge-info 2/0
WDS-MODE: ROOT-BRIDGE
BRIDGE-WLAN:
Status: OK
WlanID 1, SSID ruijie-test, BSSID 061a.a97f.1114
WBI 2/0
NONROOT 0014.4b6f.b836
LinkTime 0:00:47
SendRate 130.5M Mbps, RecvR