LED Indicator | State | Frequency | Meaning | |
| Indoor AP RAP2260(G/E) | LED Indicator | Off | N/A | The AP is NOT receiving power. |
Blinking | 0.5Hz | Normal operation, but there are alams | ||
Fast blinking | 10Hz | Possible cases: 1. Restoring the factory settings 2. Upgrading the firmware 3. Restoring the image file 4. Initializing the device | ||
Solid green | N/A | Normal operation | ||
| Indoor AP RAP2200(F/E) | LED Indicator | Off | N/A | The AP is NOT receiving power. |
Blinking | 0.5Hz | Normal operation,but the AP is not conneted to Ruijie Cloud | ||
Fast blinking | 10Hz | Possible cases: 1. Restoring the factory settings 2. Upgrading the firmware 3. Restoring the image file 4. Initializing the device | ||
Solid green | N/A | Normal operation | ||
| Wall AP RAP1200(F/P) | LED Indicator | Off | N/A | The AP is NOT receiving power. |
Blinking | 0.5Hz | Normal operation,but the AP is not conneted to Ruijie Cloud | ||
Fast blinking | 10Hz | Possible cases: 1. Restoring the factory settings 2. Upgrading the firmware 3. Restoring the image file 4. Initializing the device 5. Self-repairing | ||
(F)Solid blue (P)Solid green | N/A | Normal operation | ||
| Outdoor AP RAP6260(G) | LED Indicator | Off | N/A | The AP is NOT receiving power. |
Blinking | 0.5Hz | Normal operation,but the AP is not conneted to Ruijie Cloud | ||
Fast blinking | 10Hz | Possible cases: 1. Restoring the factory settings 2. Upgrading the firmware 3. Restoring the image file 4. Initializing the device | ||
Solid blue | N/A | Normal operation | ||
| Outdoor AP EAP602 | WiFi(Blue) | Off | N/A | WIFI is disabled |
Blinking | Data is transmitted by WiFi | |||
Solid on | WIFI is enabled and no data is transmitted | |||
| WARN(Red) | Off | Powered off or initialization test is normal. | ||
| Blinking | 1Hz | Initialization: on for 505ms and off for 505ms | ||
14Hz | Restore factory settings: on for 20ms and off for 50ms | |||
10Hz | System upgrade: on for 40ms and off for 60ms | |||
Solid on | CWMP is not connected. | |||
| LAN 1/2(Blue) | Off | N/A | The port is not connected. | |
Blinking | The port is up and data is transmitted | |||
Solid on | The port is up and no data is transmitted | |||
| Bridge EST310 | System Status | Solid green | N/A | Video recorder mode |
Fast blinking green | The system is being upgraded or reset. | |||
Slow blinking green | 2Hz | Camera mode | ||
| LAN Port Status | Solid on | The LAN port is not receiving or transmitting data. | ||
Blinking | The LAN port is receiving or transmitting data. | |||
| RSSI (3 LEDs in total) | LED 1 blinks | RSSI < -69dBm | ||
LED 1 is solid on | -69dBm< RSSI <.59dBm | |||
LED 1 and LED 2 are solid on | RSSI > -59dBm | |||
LED 1, LED 2 and LED 3 are solid on | RSSI > -49dBm | |||
Off | No signal | |||
| Bridge EST350 | System Status | Solid green | N/A | The device is working properly |
Fast blinking green | The system is being upgraded or reset. | |||
Slow blinking green | 1Hz | The device is being boot. | ||
| LAN Port Status | Solid green | The LAN port is not receiving or transmitting data. | ||
Blinking | The LAN port is receiving or transmitting data. | |||
| RSSI (3 LEDs in total) | STR1 blinking/on | The device is bridged | ||
STR1 on | RSSI > -75dBm | |||
STR1 on + STR2 blinking | RSSI > -73dBm | |||
STR1 on + STR2 on | RSSI > -71dBm | |||
STR1 on + STR2 on + STR3 blinking | RSSI > -68dBm | |||
STR1 on + STR2 on+ STR3 on | RSSI > -64dBm |
| Welcome to Ruijie Community (https://community.ruijienetworks.com/) | Powered by Discuz! X3.2 |