Ruijie Community

Title: Rates in 802.11ax and 802.11ac under 1x1 spatial flow (MCS rates for 802.11ac and 802.11ax) [Print this page]

Author: huanglinjian@ru Time: 2022-5-5 09:46
Title: Rates in 802.11ax and 802.11ac under 1x1 spatial flow (MCS rates for 802.11ac and 802.11ax)
802.11ax

802.11ac

Author: mirza.ramadhana Time: 2024-12-4 12:27
Dear henry
Can I help you with the AP configuration below, is it in accordance with the data mapping above?

interface Dot11radio 1/0
ofdma enable
country-code ID
radio-type 802.11b
mu-mimo enable
no txbf enable
rate-set 11b mandatory 11
rate-set 11b disable 1 2 5
rate-set 11g mandatory 11
rate-set 11g support 12 18 24 36 48 54
rate-set 11g disable 1 2 5 6 9
rate-set 11a mandatory 12 24
rate-set 11a support 18 36 48 54
rate-set 11a disable 6 9
rate-set 11n mcs-support 15
rate-set 11ac mcs-support 19
rate-set 11ax mcs-support 23

interface Dot11radio 2/0
ofdma enable
country-code ID
no short-preamble
radio-type 802.11a
mu-mimo enable
no txbf enable
rate-set 11a mandatory 12 24
rate-set 11a support 18 36 48 54
rate-set 11a disable 6 9
rate-set 11n mcs-support 15
rate-set 11ac mcs-support 19
rate-set 11ax mcs-support 23

Author: v-xiewenyu@ruij Time: 2024-12-4 14:07

Mirza Ramadhana replied at 2024-12-4 12:27
Dear henry
Can I help you with the AP configuration below, is it in accordance with the data mapping ...

Dear sir,
Good day.
If you're aiming to optimize performance, these settings are well-suited for modern deployments. However, ensure compatibility with legacy devices in your environment before deploying.

Best regards,
Lex

Author: mirza.ramadhana Time: 2024-12-4 15:33

GTAC-Lex replied at 2024-12-4 14:07
Dear sir,
Good day.
If you're aiming to optimize performance, these settings are well-suited for m ...

Hi Lex
Yes my objective setting is to improve performance speed local transfer for client to NAS via Wireless. Before optime rate-set i've only get speed below 3Mb/sec (file transfers). After optime by disabling low data rate better up to 10Mb/sec in radio 5Ghz. Can the mcs rate-set below still change and at what number exactly?
interface Dot11radio 1/0
ofdma enable
country-code ID
radio-type 802.11b
mu-mimo enable
no txbf enable
rate-set 11n mcs-support 15
rate-set 11ac mcs-support 19
rate-set 11ax mcs-support 23

Author: v-xiewenyu@ruij Time: 2024-12-4 18:58

Mirza Ramadhana replied at 2024-12-4 15:33
Hi Lex
Yes my objective setting is to improve performance speed local transfer for client to NAS v ...

Dear sir，
Good day.

Increase the number of spatial streams if the hardware supports it (e.g.,
rate-set 11ac mcs-support 39
for 4 spatial streams).
Enable wider channels (e.g., 160 MHz for 802.11ax).
Ensure the environment supports advanced features like MU-MIMO and OFDMA effectively.

Best regards,
Lex

Welcome to Ruijie Community (https://community.ruijienetworks.com/)