Ruijie Community

Title: How to configure speed limit for Ruijie AP in Fat Mode ? [Print this page]

Author: panjingyi1@ruij Time: 2022-6-21 15:08
Title: How to configure speed limit for Ruijie AP in Fat Mode ?
Applied scenarios
Customers can choose according to actual network conditions to configure speed limitation for wireless clients.

Case of configuration
a) Based on the entire AP speed limit command

Ruijie(config)#wlan-qos ap-based { per-user-limit | total-user-limit } { down-streams | up-streams } average-data-rate average-data-rate burst-data-rate burst-data-rate

Note:
per-user-limit // Speed limit for each user on the AP
total-user-limit //Speed limit on the entire AP
down-streams //Indicates that the downlink traffic rate limit parameters of the AP are set.
up-streams    //Indicates that the upstream traffic rate limit parameters of the AP are set.
average-data-rate    //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.
burst-data-rate //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
ha
Example: Set the average downlink rate of each user on the AP to 800KB/s and the burst rate to 1600KB/s.

Ruijie(config)#wlan-qos ap-based per-user-limit down-streams average-data-rate800 burst-data-rate 1600

b) Speed limit command based on SSID

Ruijie(config)#wlan-qos wlan-based {wlan-id |ssid } { per-user-limit | total-user-limit }{down-streams | up-streams } average-data-rate average-data-rate burst-data-rate burst-data-rate

Note:
per-user-limit    // Speed limit per user on wlan/ssid
total-user-limit    // Speed limit on the entire wlan/ssid
down-streams    //Indicates setting the downlink traffic rate limit parameter of wlan/ssid.
up-streams    // Indicates setting the upstream traffic rate limit parameters for wlan/ssid.
average-data-rate    //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.
burst-data-rate //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
Example: Set the average downlink rate of each user on wlan/ssid to 800KB/s and the burst rate to 1600KB/s.

Ruijie(config)#wlan-qos wlan-based per-user-limit down-streams average-data-rate 800burst-data-rate 1600

c) Speed limit command based on individual user

Ruijie(config)#wlan-qos netuser mac-address { inbound | outbound } average-data-rateaverage-data-rate burst-data-rate burst-data-rate

Note:
mac-address    // Indicates the user MAC address to be set.
inbound       // Indicates setting the user's upstream traffic rate limit parameters
outbound       // Indicates that the user's downlink traffic rate limit parameter is set
average-data-rate    //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.
burst-data-rate //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
Example: Set the average uplink rate of user 0000.0000.0001 to 800KB/s and the burst rate to 1600KB/s

Ruijie(config)#wlan-qos netuser 0000.0000.0001 inbound average-data-rate 800 burst-data-rate 1600

Verify
1) Ruijie#show dot11 ratelimit wlan // Indicates that the speed limit information of all WLANs is displayed.
2) Ruijie#show dot11 ratelimit user // Indicates that the speed limit information of all users is displayed.
3) Ruijie#show dot11 ratelimit ap // Indicates that the speed limit information of all APs is displayed.

Welcome to Ruijie Community (https://community.ruijienetworks.com/)