Ruijie Community

Title: How to configure PBR on ruijie EG？ [Print this page]

Author: Daisy Time: 2022-7-2 15:16
Title: How to configure PBR on ruijie EG？
I want VLAN 1 go through WAN 1, VLAN 2 go through WAN 2， how can I do it?

You can use the policy route to do it, for example
   vlan 1 is 192.168.1.0 vlan 2 is 192.168.2.0.
   WAN 1 is 10.100.10.1,  gateway is 10.100.10.254
   WAN 2 is 10.100.11.1，gateway is 10.100.11.254

Step 1 click route policy-base route， click add ACL

Step 2, Add two ACL 10 and 11，set ACE to permit 192.168.1.0 and 192.168.2.0

Step 3 Configure Policy route

Finished

Author: tengsern.tan@uc Time: 2023-7-20 12:48
this is for VLAN, what about specific IP address (one client/server) only?

Author: yujiamin@ruijie Time: 2023-7-20 13:23

The Wi-Fi Hero replied at 2023-7-20 12:48
this is for VLAN, what about specific IP address (one client/server) only?

Dear sir

You can configure the ACL to match the specific IP address here and apply the ACL on different PBR rules.

Best regards
Jenny

Author: tengsern.tan@uc Time: 2023-7-21 09:44

GTAC-Jenny replied at 2023-7-20 13:23
Dear sir

You can configure the ACL to match the specific IP address here and apply the ACL on di ...

do i have to enable default route for both WAN?

Author: yujiamin@ruijie Time: 2023-7-21 09:51

The Wi-Fi Hero replied at 2023-7-21 09:44
do i have to enable default route for both WAN?

Dear sir

Yes, the default route will be added by default when you set the port to WAN port to make sure the user internet access. You can type this command: show ip route to check the EG routing.

Best regards
Jenny

Author: janzsaludaga199 Time: 2023-12-27 23:06
hello how about 3 ISP
i want this vlan10 go only ISP 1
but vlan 20 go only ISP 2 and ISP 3

Author: rickywong@multi Time: 2024-1-31 18:04
Will the Extended ACL work with PBR also?

For example,

when the Destination port is UDP 443, the Route to wan1
when the Source port is UDP 53, the Route to wan2

Author: eddz1st@gmail.c Time: 2024-9-24 21:07
Hello, can you show some configuration if there is more than 2 WAN..

example :
VLAN 20 and 30 via WAN 1 , WAN 2 , WAN 3 ( Load balanced )

and
VLAN 40 via WAN 4 and WAN 5 ( load balanced )
is this possible?

Author: v-xiewenyu@ruij Time: 2024-9-24 23:00

XjawZx replied at 2024-9-24 21:07
Hello, can you show some configuration if there is more than 2 WAN..

example :

Dear Sir,
Good day.
To configure PBR on ruijie EG, you may check this configuration guide:
https://www.ruijienetworks.com/resources/preview/ruijie-reyee-rg-eg-series-gateways-web-based-configuration-guide-B16/

Best regards,
Lex

Welcome to Ruijie Community (https://community.ruijienetworks.com/)