Ruijie Community

Title: mib for vlan in ruijie [Print this page]

Author: hendranata@nata Time: 2022-10-12 16:18
Title: mib for vlan in ruijie
helo
anybody know what is the exactly mib code for ruijie to be able to draw vlan ?
information we use: ifOutOctets mib 1.3.6.1.2.1.2.2.1.16

vlan show 0 value..

IF-MIB::ifOutOctets.4096 = Counter32: 0
IF-MIB::ifOutOctets.4165 = Counter32: 0
IF-MIB::ifOutOctets.4166 = Counter32: 0

any idea or am i using wrong MIB code?
thanks

Author: hendranata@nata Time: 2022-10-12 16:25
in this case we use cacti for the software monitoring.. if u have device template for ruijie switch RG-S6220-48XS6QXS-H.. it would be good..

thanks

Author: GTAC-Micca Time: 2022-10-13 17:56
This function is disabled by default, and you have not configure it, please try config it for vlan interface.

Author: hendranata@nata Time: 2022-10-14 11:46
Edited by hendranata saputra at 2022-10-14 11:48

Micca replied at 2022-10-13 17:56
This function is disabled by default, and you have not configure it, please try config it for vlan i ...

we have enable it right now.

interface VLAN 71
route-sample enable
ip address xxx.yyy.ddd.254 255.255.255.128
!

CoreSw#sh int v71
Index(dec):4167 (hex):1047
VLAN 71 is UP  , line protocol is UP
  Hardware is VLAN, address is 300d.9e42.8714 (bia 300d.9e42.8714)
  Interface address is: xxx.yyy.ddd.254/25
  ARP type: ARPA, ARP Timeout: 3600 seconds
  Interface IPv6 address is:
No IPv6 address
  MTU 1500 bytes, BW 1000000 Kbit
  Encapsulation protocol is Ethernet-II, loopback not set
  Keepalive interval is 10 sec , set
  Carrier delay is 2 sec
  IPv4 statistics:
0 seconds input rate 0 bits/sec, 0 packets/sec
0 seconds output rate 0 bits/sec, 0 packets/sec
   0 packets input, 0 bytes
   0 packets output, 0 bytes
  IPv6 statistics:
0 seconds input rate 0 bits/sec, 0 packets/sec
0 seconds output rate 0 bits/sec, 0 packets/sec
   0 packets input, 0 bytes
   0 packets output, 0 bytes
  Rxload is 1/255, Txload is 1/255
10 seconds input rate 0 bits/sec, 0 packets/sec
10 seconds output rate 0 bits/sec, 0 packets/sec
Input packets       0                      Input bytes          0
Input broadcasts    0                      Input multicasts    0
Input unicasts       0
Output packets       0                      Output bytes       0

the value statistic still 0.. any idea?

Author: GTAC-Micca Time: 2022-10-14 22:24

hendranata saputra replied at 2022-10-14 11:46
Micca replied at 2022-10-13 17:56
This function is disabled by default, and you have not configure i ...

Sorry, the firmware versions do not support this value statistic
at present.

Author: hendranata@nata Time: 2022-10-15 08:17

Micca replied at 2022-10-14 22:24
Sorry, the firmware versions do not support this value statistic
at present.

route-sample enable... it is not working in your official doc ?
hemm.. do u have any solution for this ruijie model S6220-48XS6QXS-H

Welcome to Ruijie Community (https://community.ruijienetworks.com/)