Ruijie Community

Title: Ruijie EW 1200G Pro and EW 1300G Connection Problem. [Print this page]

Author: K.M._25 Time: 2024-5-17 08:07
Title: Ruijie EW 1200G Pro and EW 1300G Connection Problem.
I just bought new Wireless Router that 2 models.
1200G pro and 1300G Using Router mode like this.

But i always get disconnected and change into another wifi connection.
The firmware already the latest Version.
What should i do?
Can give me advice how to setting it properly ?
Thankyou.
Btw,Client only 10-15 devices for each router.

Author: taizhaolong@rui Time: 2024-5-17 08:47
Dear,

Regarding the issue that client get disconnected and change into another wifi connection, do you mean the users would connect to other WIFI not from 1200G pro and 1300G ?

And were users' devices moving around or being still when the disconnection occurred ?

For most of end devices, they would switch to wifi with stronger signal if detected.
You may adjust the power on 1200G pro and 1300G and see if it would help

RD,

David

Author: K.M._25 Time: 2024-5-17 09:15

GTAC-David replied at 2024-5-17 08:47
Dear,

Regarding the issue that client get disconnected and change into another wifi connection, do ...

Yes.
The user connect into another connection not from the wirelss router 1200G pro.
Can give me advice to setting it properly?
Thank you.

Author: liuxiyang@ruiji Time: 2024-5-17 10:34

kalep Manulang replied at 2024-5-17 09:15
Yes.
The user connect into another connection not from the wirelss router 1200G pro.
Can give me a ...

Hi sir,
The SSID of the device is selected by the user for connection. If you want the user to specify the connection to a certain device, you can configure the blacklist on another device.

Best regards,
Steve

Author: K.M._25 Time: 2024-5-17 11:03
Edited by K.M._25 at 2024-5-17 11:14

GTAC-Steve replied at 2024-5-17 10:34
Hi sir,
The SSID of the device is selected by the user for connection. If you want the user to spe ...

I mean , user easily disconneted from the router and connect into another wifi connection.
Could you like give me the proper setting so the user won't easily disconnected?
Cek the firmware already the latest and also i reset the router and rebuiild the setting from the beginning also.

Thank you

Author: wengjialong@rui Time: 2024-5-17 13:17

K.M._25 replied at 2024-5-17 11:03
GTAC-Steve replied at 2024-5-17 10:34
Hi sir,
The SSID of the device is selected by the user for con ...

Hi, K.M._25

May I please know if the 2 routers are both working in Router mode and are they broadcasting different SSIDs or the same SSID?
What is the distance between the 2 routers? If they are near each other, please reduce the transmit power on the routers.

Best regards,
Jayden

Author: kalep40@gmail.c Time: 2024-5-17 18:06

GTAC-Jayden replied at 2024-5-17 13:17
K.M._25 replied at 2024-5-17 11:03
GTAC-Steve replied at 2024-5-17 10:34
Hi sir,

Hi,sir.
The router is in different place and kinda far

i put as router mode and radio frequency is in auto

Author: yujiamin@ruijie Time: 2024-5-20 14:40

K.M._25 replied at 2024-5-17 18:06
Hi,sir.
The router is in different place and kinda far

Hi, K.M._25

1. You can try to modify the router power to be appropriate and to avoid the signal interrupt between the routers. The ideal signal strength is -65dbm in router coverage area edge.
2. The adjacent router channels must be non-overlapped channel to avoid same frequency interference and packet loss. For example in non-high-density deployment scenarios, 2.4G channels are recommended to use 3 non-overlapping channels 1, 6, and 11 for planning. If it is a high-density deployment site, it is recommended to use 4 channels 1, 5, 9, and 13 for planning; 5G channels are recommended to use 149, 153, 157, 161, 165, 36, 40, 44, 48, 52, 56, 60, 64, a total of 13 non-overlapping channels are planned.
3. It is client behaviour to choose which router to connect. If the clients can support modifying the roaming sensitivity, you can change to decrease roaming sensitivity via More> WLAN> Radio Frequency.to test again. If the client can not support the setting, we can try to modify the roaming sensivity on both routers to see whether the user still disconnect repeatedly.

Best regards
Jenny

Welcome to Ruijie Community (https://community.ruijienetworks.com/)