Fit AP SNMP Config
|
Hello, I have many Access Points (AP820 V2) that work in fit mode (managed by a controller). I made SNMP settings on the controller, but the APs that work in Fit Mode do not have these SNMP settings. When I activate manual SNMP on the AP, the settings are deleted in the first config sync process. I couldn't send snmp config to the ap because there was no snmp-server argument in ap-config all in the controller cli. Is there a way to send these SNMP settings via the controller? Note: I think the snmp settings on the controller are only valid for the controller. I've already tried this. |
|
You can run the ap-group command on the ac to access the ap group and configure snmp configurations for the ap group in batches |
GTAC-Thomas replied at 2025-3-12 21:23 I have a default group but how does the snmp setting relate to this? Can you provide details? Thanks. |
GTAC-Thomas replied at 2025-3-12 21:23 where is the snmp configuration? Ruijie(config-group)#? Ap Group Commands: 6GHz Set the 6GHz. 802.11a Set the 802.11a. 802.11b Set the 802.11b. 802.11g Set the 802.11g. ac-domain-name Set ac domain name which the Ap connect to. ampdu-depth Config ampdu-depth antenna Config antenna mask ap-announcement-mode Set announcement mode ap-idle-timeout Set ap idle timeout ap-image Set ap image file should run ap-interface Ap interface ap-intf-statistics Ap interface statistics ap-mode Set WTP Mode auto-cfg Auto sync cfg file to ap auto-join-group Set AP auto join group. autowds Set auto wds backup-controller-primary Set ap backup primary ac ip backup-controller-secondary Set ap backup secondary ac ip backup-controller-tertiary Set ap backup tertiary ac ip band-optimize 11ax(11ac) navigating function config blacklist Blacklist bss-color Set BSS Color capwap Capwap config cell-range-reduction Set the ap-group's cell range reduction channel-mode Set ap channel mode clink Ap group for clink coverage-area-control Coverage-area-control credential Set ap group's ap credential. data-plane Set data-plane default Set a command to its defaults dhcp Enable dhcp dns dhcp-option Dhcp pool optioin dns Dns config do To run exec commands in config mode dynamic-pool Dynamic dhcp pool echo-interval Time between echo request messages end Exit from ap group mode exec-cmd Execute command in all ap-config in this group exit Exit from ap group mode extra-coverage Config extra-coverage hap-poe Enable default radio if power low help Description of the interactive help system inter-radio-balance Inter-radio STA balance function interface-mapping Set the interface map, ssid -- vid peer. link-latency Set the link latency test master-group Config master group. mu-mimo Config MU-MIMO multi-bssid Set multi-bssid network Network config no Negate a command or set its defaults ofdma Config ofdma offline-ssid Set AP offline SSID. power Set power local power-max Set ap radio tx power max mode power-out Configure power out. primary-base Set ap primary ac name priority Set ap group's ap failover priority quiet-mode Config ap-group quiet_mode ript Configure ript rnr Set rnr rrm Rrm schedule Config ap-group schedule secondary-base Set ap secondary ac ip service Service dhcp show Show running system information sta-idle-timeout Set the Idle Timeout sta-limit Set the limit STA attached to this AP statistics-timer Set the Statistics Timer sticky-steering Ap-group for sticky steering tertiary-base Set ap tertiary ac ip timestamp Set the AP's timestamp as the AC's. tunnel Config forward type twt Set TWT txbf Config TxBF virtual-ap Add virtual AP whitelist Whitelist wired-interface Config the APG's wired interface wired-rate Config rate of wired interfaces wired-vlan Config the APG's wired vlan |
ssahin replied at 2025-3-14 16:51 Hi sir, Configure the SNMP read and write community and SNMP server on the AC, and send the AC to the AP. Ruijie(config)#snmp-server community XX (where XX is the snmp community) rw (be sure to configure it as rw, read-write) Ruijie(config)#snmp-server host server IP traps version 2c XX (where XX is the snmp community) Best regards, Steve |
|
Hello, I mentioned it in my previous posts but I guess you didn't pay attention. I already made snmp settings on Ruijie ac. SNMP is currently working on the controller but unfortunately these settings are not available on the Access point side. AC; snmp-server location DEMO snmp-server host x.x.x.x traps version 2c **CommunityName** snmp-server enable traps snmp-server community **CommunityName** rw The Access point I manage from this controller does not receive these settings from the controller. I think the snmp settings are not syncing. |
ssahin replied at 2025-3-14 17:15 hello, the solution was with ap-config. Thank you to the support team. The commands are as follows; on AC; configure terminal ap-config all exec-cmd mode configure cmd "snmp-server location TESTLOCATION" exec-cmd mode configure cmd "snmp-server community COMMUNITYSTRING rw" end write if you wish, you can also define traps after the exec-cmd mode configure cmd command. |
This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.
More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.
©2000-2023 Ruijie Networks Co,Ltd
Level 1
