cant config wan0 + wan1 with wifi employee + guest

i have project  with EG210G-p  + RAP2260 ( 12 unit )
i config 2 wifi    employye / guest ...  the guest wifi should use internet from wan1 only

anybody do this before  . i try many things but i guess ist not possible .

Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configure Load Balance



2.Configure ACL: Block Guest IP address pass through WAN0

Toby1 replied at 2023-2-7 16:21
Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configur ...

hi bro thanks for your reply .
but it doesn't work. still the guest Wi-Fi can access the internet throw wan-0

simply. the need is  
Wi-Fi employee use only wan-0
Wi-Fi guest use only wan-1
no balance or fail over need.

my network config ,
Wi-Fi emp ip(192.168.22.1)vlan defult  / wan-0  ip (192.168.3.11)
Wi-Fi guest ip (192.168.33.1)vlan33 / wan-1 ip (192.168.5.13)

Issa Yaser replied at 2023-2-10 01:03
hi bro thanks for your reply .
but it doesn't work. still the guest Wi-Fi can access the internet  ...

Bro, could you try the following configuration?

Toby1 replied at 2023-2-10 12:26
Bro, could you try the following configuration?

bro
the same doesn't work. still Wi-Fi guest can access internet throw another wan .
i reset all the project and reconfigure all devices. but same result


i think this device can't be secure on network. and can't divided wan's

Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access internet throw another wan .
i reset all  ...

Hi, bro.
Could you refer this link to do a configuration :https://www.ruijienetworks.com/resources/preview/77309
On the page 65.

Toby1 replied at 2023-2-7 16:21
Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configur ...

How can I find more informations?

Steve replied at 2023-2-13 09:22
Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access inter ...

hi bro

i do everything. but same result still doesn't work.

Steve replied at 2023-2-13 09:22
Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access inter ...

dear
i do everything. step by step .
but doesn't work. the Wi-Fi network still can access both wans.

Issa Yaser replied at 2023-2-16 06:04
dear
i do everything. step by step .
but doesn't work. the Wi-Fi network still can access both w ...

Hi bro,
Could you please share your network with me? This is my email:liuxiyang@ruijie.com.cn

GTAC-Steve replied at 2023-2-16 09:08
Hi bro,
Could you please share your network with me? This is my email:liuxiyang@ruijie.com.cn

Hi I have the same issue but cannot find how to get this working. Can i get some assistance.
I have 2 vlans:    VLAN2 for guest 192.168.2.1-254 and VLAN 1 for admin 192.168.1.1-254. both have their own SSID's

I want Vlan1 to use WAN0 and WAN 1 as fail over, and VLAN2 use WAN2
i cannot figure it out

Dear All,
Good day to you ! are you able to overcome this issue ! I would like to configure the same setting on my customer side using EG305GH-P-E which using 2 difference ISP provider. Hopefully you able to overcome this issue

Thank you

User 58099 replied at 2023-11-21 02:51
Dear All,
Good day to you ! are you able to overcome this issue ! I would like to configure the sam ...

Hi sir,

please kindly refer to this link to configure it :https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=5720


Best regards,
Steve

GTAC-Steve replied at 2023-11-21 14:34
Hi sir,

please kindly refer to this link to configure it :https://community.ruijienetworks.com/fo ...

Dear Steve,
thank you for your reply ! but what I means is certain ip address to redirect to Wan 2 of the Another ISP provider instead using load
balancing on  RG-EG305GH-P-E , which about the same question of the  user
cant config wan0 + wan1 with wifi employee + guest
1195122023-2-6 22:18:55

asking about !  any idea to configure it

thank you

User 58099 replied at 2023-11-22 23:27
Dear Steve,
thank you for your reply ! but what I means is certain ip address to redirect to Wan  ...

Dear:

Have you tried to deploy this config but using PBR on your reyee EG?

If not, please refer to the following link:

https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=4010

The scenario presented shows how to reach internet only
using one ISP.

Regards,

Javier

GTAC--Javier replied at 2023-11-23 08:59
Dear:

Have you tried to deploy this config but using PBR on your reyee EG?

Dear Javier ,
will try on PBR on your reyee EG way to do it . thank you

But  If my customer having 3 Wan ISP link , how do I configure it , using the following link above way to configure PBR to route WAN 3?


Thank you

User 58099 replied at 2023-11-24 02:22
Dear Javier ,
will try on PBR on your reyee EG way to do it . thank you

Dear:

Sorry, I think I was not clear enough. The link that I shared with you explains how to forward traffic through only one WAN interface when you are currently using 2 or more egress interfaces (which would be multi-WAN scenario, just like in your project). So, you can follow the steps as explained in the link

Regards,

Javier

GTAC--Javier replied at 2023-11-24 08:05
Dear:

Sorry, I think I was not clear enough. The link that I shared with you explains how to forw ...

Dear Javier,
  Thank you for your email. you not clear my question sometime.. that why I prefer draw a diagram to you, As well I also not clear your explain to me sometime .sorry .. anyway thank you for your help to answer my question . So ,you answer my the question " you can follow the steps as explained in the link"

you means this link https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=4010?

thank you