| how to collecting information when VSU fails |
|
Step1: Check the status of the Virtual Switch Unit (VSU)system. Check the status of the VSU system todetermine whether the network is disconnected due to VSU failure. (1) Check whether VSU configurations arecorrect. ruijie#show switch virtual config (2) Check whether Virtual Switching Links(VSLs) are normal. ruijie#show sw vir link ruijie#show sw vir link port//Check whether VSLs are normal. If yes, the VSU system is not split. ruijie#show int count error ruijie#show int trans //If VSLs are created using opticaltransceivers, check the optical transceivers. ruijie#show int trans dia //If VSLs are created using opticaltransceivers, check optical attenuation of the fiber. (3) If all VSLs go down, log in to twoswitches at link ends to check whether one of them enters the recovery mode.The one entering recovering mode is the standby. ruijie#show sw virtual dual-active summary BFDdual-active detection enabled: Yes Aggregateportdual-active detection enabled: NO In dual-active recovery mode: Yes //At least one switch should be in therecovery mode. If neither one enters the recovery mode, VSLs are abnormal andthe dual-active detection is disabled when two active switches exist. (4) If one switch enters the recovery mode(all its interfaces are shut down this time), check whether the disconnectedPCs connect to the standby switch. If yes, re-connect the PCs to the activeswitch to avoid the influence of the recovering mode. (5) If all VSLs go down, check whether thefault is caused by software problems or link disconnection. a.Enter the management board and the corresponding VSL line card to check whethercrash information exists. Run the following commands to collect faultinformation: Ruijie#debug support Ruijie(support)#tech-supportpackage b.Check whether the keepalive timeout information of the line card is logged. c.Check whether the abnormal reset of management board (not crash) is logged. (1) Run the show arp command tocheck whether the switches in disconnected network segments can learn MAC addresses. (2)Check by CPP whether related packets aresent to the CPU. (You have to check packets under protocols enabled in thenetwork especially for connectivity protocols, for example, ARP, VRRP, andBPDU.) Runeach of the following commands for five times: Ruijie#show cpu-pro Ruijie#show cpu-pro mb Ruijie#show cpu-protect slot X //X indicates the slot ID. For example, run show cpu-pro slot 4 to display information of Slot 4 on thestandalone server S86E; run show cpu-proslot 2/4 to display information of Slot 4 on Cabinet 2 of the VSU system. If thenumber of packets sent to the CPU of the line card or management board isalways 0, the packet reception by CPU is abnormal. Ruijie#show int count rate //Check whether the interface rate exceedsthe interface bandwidth. Ruijie#show int count summary //Checkwhether the interface input/output broadcast packets increase rapidly. If yes,a loop must have occurred in the network. Ruijie#show cpu //Check whether CPU resources ofthe VSU system are normal. Ruijie#show memory //Check the memory utilization of the VSUsystem. Ruijie#debug support Ruijie(support)#tech-support package Step5: Collect and summarize log information.Collect log information (enable the timestamp and ensure time accuracy) and provide it to Ruijie technical support foranalysis. Collect basic information: ruijie>enable ruijie# ---------In Privileged EXEC Mode(ruijie#)---------------- show ver show ver slot show run show cpu show memory show logging show cpu-protect show cpu-protect mb show cpu-protect slot X //X indicates the slot ID. For example, runshow cpu-pro slot 4 to displayinformation of Slot 4 on the standalone server S86E; run show cpu-pro slot 2/4 to display information of Slot 4 on Cabinet 2of the VSU system. show interfaces counters rate show interfaces counters show int count summary show int count error show mac-address-table show arp show mac-address-table count show arp count Collect VSU information: ruijie>enable ruijie# ---------In Privileged EXEC Mode(ruijie#)---------------- show switch virtual link show switch virtual link port show switch virtual config show switch virtual role |
This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.
More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.
©2000-2023 Ruijie Networks Co,Ltd
Level 1
