Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The category of your feedback

Your Feedback

Your Email address (optional):

How to configure PBR on ruijie EG? Reply

GTAC-Daisy

Level 1

How to configure PBR on ruijie EG?
5272 8 2022-7-2 15:16:40
Original
I want VLAN 1 go through WAN 1, VLAN 2 go through WAN 2, how can I do it?


You can use the policy route to do it, for example
     vlan 1 is 192.168.1.0   vlan 2 is 192.168.2.0.
     WAN 1 is 10.100.10.1,  gateway is 10.100.10.254
     WAN 2 is 10.100.11.1,gateway is 10.100.11.254


Step 1 click route policy-base route, click add ACL



Step 2, Add two ACL 10 and 11,set ACE to permit 192.168.1.0 and 192.168.2.0






Step 3 Configure Policy route


Finished

RG-EG2100-P v2

Router
0 2023-7-20 12:48:32 View all replies
this is for VLAN, what about specific IP address (one client/server) only?

0 2023-7-20 13:23:25 View all replies
The Wi-Fi Hero replied at 2023-7-20 12:48
this is for VLAN, what about specific IP address (one client/server) only?

Dear sir

You can configure the ACL  to match the specific IP address here and apply the ACL on different PBR rules.



Best regards
Jenny

0 2023-7-21 09:44:19 View all replies
GTAC-Jenny replied at 2023-7-20 13:23
Dear sir

You can configure the ACL  to match the specific IP address here and apply the ACL on di ...

do i have to enable default route for both WAN?

0 2023-7-21 09:51:55 View all replies
The Wi-Fi Hero replied at 2023-7-21 09:44
do i have to enable default route for both WAN?

Dear sir

Yes, the default route will be added by default when you set the port to WAN port to make sure the user internet access. You can type this command: show ip route to check the EG routing.

Best regards
Jenny

0 2023-12-27 23:06:57 View all replies
hello how about 3 ISP
i want this vlan10 go only ISP 1
but vlan 20 go only ISP 2 and ISP 3

0 2024-1-31 18:04:02 View all replies
Will the Extended ACL work with PBR also?

For example,

when the Destination port is UDP 443, the Route to wan1
when the Source port is UDP 53, the Route to wan2


0 2024-9-24 21:07:07 View all replies
Hello, can you show some configuration if there is more than 2 WAN..

example :
VLAN 20 and 30 via WAN 1 , WAN 2 , WAN 3 ( Load balanced )

and
VLAN 40 via WAN 4 and WAN 5 ( load balanced )
is this possible?

0 2024-9-24 23:00:42 View all replies
XjawZx replied at 2024-9-24 21:07
Hello, can you show some configuration if there is more than 2 WAN..

example :

Dear Sir,
Good day.
To configure PBR on ruijie EG, you may check this configuration guide:
https://www.ruijienetworks.com/resources/preview/ruijie-reyee-rg-eg-series-gateways-web-based-configuration-guide-B16/

Best regards,
Lex

Related Posts
Product Model

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2023 Ruijie Networks Co,Ltd