Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The category of your feedback

Your Feedback

Your Email address (optional):

Dynamic Vlan & Disable low data rates on MACC controller Reply

Johan

Level 1

Dynamic Vlan & Disable low data rates on MACC controller
5051 3 2021-5-19 14:25:25
Original
I have Ruijie rg-ap820-l(v2) and already configured on Cloud Controller. 1. How to configure SSID with dynamic vlan assignment from Radius Server with 802.1x authentication,

2. How to disable low data rates 1 and 2  Mbps, I tried the command but seems not working
rate-set 11b mandatory 5 11
rate-set 11g mandatory 5 11

0 2021-5-19 19:26:21 View all replies
1.you can do as the following way
  (1)configure SSID on cloud

  

  (2)configure snmp

    AP(config)#snmp-server community ruijie123 rw

  (3)add AP to radius server
  (4)Confiure vlan-group and dynamic vlan
APtest(config)#vlan 10
APtest(config-vlan)#vlan 20
APtest(config-vlan)#exit

APtest(config)#vlan-group 10
APtest(config-vlan-group)#vlan-list 1,10,20
APtest(config-vlan-group)#default-vlan 1
APtest(config-vlan-group)#exit

   (5)check the vlan group
APtest(config)#show vlan-group 10

   (6)Encapsule vlan-group to radio
APtest(config)#interface Dot11radio 1/0.1
APtest(config-subif-Dot11radio 1/0.1)#no encapsulation
APtest(config-subif-Dot11radio 1/0.1)#encapsulation dot group 10
APtest(config-subif-Dot11radio 1/0.1)#int dot 2/0.1
APtest(config-subif-Dot11radio 2/0.1)#no encapsulation
APtest(config-subif-Dot11radio 2/0.1)#encapsulation dot group 10
APtest(config-subif-Dot11radio 2/0.1)#exit

APtest(config)#int gi 0/1.1
APtest(config-subif-GigabitEthernet 0/1.1)#encapsulation dot group 10
APtest(config-subif-GigabitEthernet 0/1.1)# ip dhcp snooping trust
APtest(config-subif-GigabitEthernet 0/1.1)#end
APtest#wr

   (7)configure the user on radius server


2. please type command 'show dot a a' to check

0 2021-5-20 11:28:40 View all replies
Edited by jharianto@njis.org at 2021-5-20 14:16

1. Ok, I'll try that.

2. Here is the output, on the controller manual & forum, I saw that we can use 802.11g rate 1 2 disable, but how disable it on MACC mode controller?

here is the output from the Inssider, that showing 1,2 rates still enabled

0 2021-5-20 17:20:01 View all replies
sir,You can create Case in Caseportal, or contact our online support Rita , in order to conduct further investigation,Thank you.

caseportal:[https://caseportal.ruijienetworks.com/
Rita:https://www.sobotws.cn/chat/pc/v ... 569a4791536fb5f0973

Related Posts
Product Model

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2023 Ruijie Networks Co,Ltd