How to configure multiple speed limit modes in wireless fat mode

Applied scenarios
Customers can choose according to actual network conditions to configure speed limitation for wireless clients.

Case of configuration
a) Based on the entire AP speed limit command

Ruijie(config)#wlan-qos ap-based { per-user-limit | total-user-limit } { down-streams | up-streams } average-data-rate  average-data-rate burst-data-rate burst-data-rate  

Note:
per-user-limit   // Speed limit for each user on the AP
total-user-limit    //Speed limit on the entire AP      
down-streams    //Indicates that the downlink traffic rate limit parameters of the AP are set.      
up-streams     //Indicates that the upstream traffic rate limit parameters of the AP are set.      
average-data-rate     //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.   
burst-data-rate    //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
ha
Example: Set the average downlink rate of each user on the AP to 800KB/s and the burst rate to 1600KB/s.

Ruijie(config)#wlan-qos   ap-based per-user-limit down-streams average-data-rate800 burst-data-rate 1600   

b) Speed limit command based on SSID

Ruijie(config)#wlan-qos wlan-based {wlan-id |ssid } { per-user-limit | total-user-limit }{down-streams | up-streams } average-data-rate average-data-rate  burst-data-rate burst-data-rate

   
Note:
per-user-limit      // Speed limit per user on wlan/ssid               
total-user-limit      // Speed limit on the entire wlan/ssid   
down-streams     //Indicates setting the downlink traffic rate limit parameter of wlan/ssid.      
up-streams       // Indicates setting the upstream traffic rate limit parameters for wlan/ssid.
average-data-rate     //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.   
burst-data-rate    //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
Example: Set the average downlink rate of each user on wlan/ssid to 800KB/s and the burst rate to 1600KB/s.

Ruijie(config)#wlan-qos wlan-based per-user-limit down-streams average-data-rate 800burst-data-rate 1600

  
c) Speed limit command based on individual user

Ruijie(config)#wlan-qos netuser mac-address { inbound | outbound } average-data-rateaverage-data-rate burst-data-rate burst-data-rate

Note:
mac-address      // Indicates the user MAC address to be set.  
inbound        // Indicates setting the user's upstream traffic rate limit parameters   
outbound         // Indicates that the user's downlink traffic rate limit parameter is set
average-data-rate     //Indicates to set the average rate limit, the unit is 8Kbps, the range is 8-261120.   
burst-data-rate    //Indicates to set the burst rate limit, the unit is 8Kbps, the range is 8-261120.
Example: Set the average uplink rate of user 0000.0000.0001 to 800KB/s and the burst rate to 1600KB/s

Ruijie(config)#wlan-qos netuser  0000.0000.0001 inbound average-data-rate  800  burst-data-rate 1600

Verify
1) Ruijie#show dot11 ratelimit wlan    // Indicates that the speed limit information of all WLANs is displayed.
2) Ruijie#show dot11 ratelimit user   // Indicates that the speed limit information of all users is displayed.
3) Ruijie#show dot11 ratelimit ap    // Indicates that the speed limit information of all APs is displayed.