Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The Category of your Feedback

Your Feedback

Your Email Adress(optional)

Products

VLAN on AP130(W2) Reply
VLAN on AP130(W2)
600 3 2022-9-26 18:09:52
Hi
   Need your support regarding port VLAN configuration as per our topology below :
- default VLAN(208) on port 1 trunk mode.
- port 2-5 use VLAN (600) access mode.
i used configuration below:
vlan 1
vlan 208
vlan 600
1. Trunk Port :
interface GigabitEthernet 0/1
encapsulation dot1Q 1
!
ip dhcp snooping trust
interface GigabitEthernet 0/1.208
encapsulation dot1Q 208
!
ip dhcp snooping trust
interface GigabitEthernet 0/1.600
encapsulation dot1Q 600
ip dhcp snooping trust
!
2. Access Port :
!
interface GigabitEthernet 0/2
encapsulation dot1Q 600
rldp port loop-detect shutdown-port
!
interface GigabitEthernet 0/3
encapsulation dot1Q 600
rldp port loop-detect shutdown-port
!
interface GigabitEthernet 0/4
encapsulation dot1Q 600
rldp port loop-detect shutdown-port
!
interface GigabitEthernet 0/5
encapsulation dot1Q 600
rldp port loop-detect shutdown-port
!
- As per configuration above port 1(trunk) carry vlan 208 and 600
- Port 2-6 (access mode) should get ip from vlan 600 , but the port still get ip from vlan 208.
Is my setting wrong? What is the right command to get the access mode port on AP130(W2).
Thank You
RG-AP130(W2)

Wireless
2 2022-9-27 09:34:06 View all replies
Hi

1. Will the user get the address from the switch or the gateway?
2. May I know how the switch port to which the AP is connected is configured? Which vlan is the Native vlan configured with? If user will get ip from gateway , please share the configuration for the uplink port of the switch.


Best regards,

GTAC-Harvey replied at 2022-9-27 09:34
Hi

1. Will the user get the address from the switch or the gateway?

Hi
1. user device get ip address from gateway (Fortigate).
2. The native VLAN use 208, the Ruijie AP130(W2) connected to trunk port switch with Native VLAN 208, and allow VLAN 600

Bagus Susanto replied at 2022-9-27 12:08
Hi
1. user device get ip address from gateway (Fortigate).
2. The native VLAN use 208, the Ruijie  ...
Hi
2. The native VLAN use 208, the Ruijie
AP130(W2) connected to trunk port switch with Native VLAN 208, and allow VLAN 600
---------------------------------------------------------------------------------------------------------------------------------------------------
Could you share the configuration for the 2 ports on switch:
1.AP  connect to switch
2.Switch connect to Gateway.

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2022 Ruijie Networks Co,Ltd