How to user Radius for aaa authentication enable

Hi,

how to use a Radius (freeradius) server for "aaa authentication enable" on RG-S6510?
When configuring the Radius the communication works for "aaa authentication login" but not for "aaa authentication enable". I get a "Access-Accept" back from the Radius but the "enable" fails with a "% Error in authentication". Can't find any further details in the logs/debug settings. Everything looks fine but "enable" fails.
Any specific attribute I need to send back from Radius? For Huawei I needed "Huawei-Exec-Privilege = 15"
I read the command reference and config guide back and forth but could not find anything in regard to this problem.
Any hint is appreciated.
Thanks
Sebastian

Some logs

switch>enPassword:% Error in authentication.

*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                                               rds_add_attribute][ 1205]  rds_add_attribute  type = 32 len = 0
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                                  rds_add_authen][  405] Add authentication success.
*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                                           rds_get_vrf_id_by_ifx][   96] get vrf id 1234 by interface index 8193
*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                                                    rds_make_pkt][ 1546] 14 send.
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                                    rds_send_pkt][  681] Send msg success.
*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                                                  rds_authen_req][  643] radius access requests(14).
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                           rds_proc_protocol_pkt][ 1127] Receive packet from server 1.2.3.4
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                         rds_get_result_from_pkt][ 1047] Radius access-accept.
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                         rds_get_result_from_pkt][ 1058] auth round trip: (1126893, 1126893, 0).
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                         rds_get_result_from_pkt][ 1092] attr resolve begin..
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                         rds_get_result_from_pkt][ 1108] attr resolve end..
*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                                           rds_get_vrf_id_by_ifx][   96] get vrf id 1234 by interface index 8193
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                                 rds_delete_user][  382] Delete user.
*Oct 13 13:36:42: switch %RDS-7-USER:   [ 2904][ 301989889, 14][                                rds_release_user][  352] Free user
*Oct 13 13:36:42: switch %RDS-7-EVENT:  [ 2904][                             rds_proc_in_msg_from_other_or_timer][ 1467] Thread[1] receive info message.

Hi, sir
May I know your firmware version?
For this situation, you may contact our engineers on Rita for further check

Patrick replied at 2022-10-14 15:09
Hi, sir
May I know your firmware version?
For this situation, you may contact our engineers on Rita  ...

Hi,
we're running 11.0(5)B9P62S6.
Thanks
Sebastian

Sebastian Wenner replied at 2022-10-17 14:32
Hi,
we're running 11.0(5)B9P62S6.
Thanks

Hi, sir.
You can try this command on cli of this switch:
conf
username xxxx privilege 15 password xxxxx
line vty 0 4
privilege level 15
end
wr

Thanks for the answers.
What actually helped was using

Service-Type = "Administrative-User"

in the reply from Radius.

Sebastian Wenner replied at 2022-10-21 18:01
Thanks for the answers.
What actually helped was using
Service-Type = "Administrative-User"

[/ ...
Thanks for your information, sir