Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The category of your feedback

Your Feedback

Your Email address (optional):

Reyee AP Mesh FAQs Reply

GTAC-Sophia

Level 5

Ruijie Staff

Reyee AP Mesh FAQs
7505 0 2022-11-2 17:15:52
Original
Introduction
Here is the FAQs about Mesh Function, hope it helpful to you~
If you have any questions about RAP mesh function, welcome leave it in the comment area, we will answer you as soon as possible~
Note
1.   All Reyee AP models support the mesh feature except RG-RAP1200(F), RG-RAP2200(F), RG-EAP602.
2.   Please upgrade the Reyee AP to the latest version (AP 3.0(1)B11P86) before you configure the mesh function.
3.   The prerequisites for AP mesh must be met at the same time: The root AP has completed the initial configuration, but the mesh AP doesn't.

-------------------------------------------------------------------------------------------------------------------------------------------------------------
FAQs
1.Can the AP only amplify the signal but not forward the wireless data when it works as the wireless repeater mode?
2. Is it necessary to associate a specific AP when establishing Mesh?
3. How to select the Root AP of the mesh AP? Is possible the selected Root AP not the optimal one?
4. Why does the wireless bandwidth of the next hop AP decrease by 50% with each additional hop?
5. Is there any number limitation of Reyee AP mesh?
6. In the SON, what's the maximum capacity when Reyee devices are wired or wireless connected?
7. If the AP is disconnected with the cable, how long does it take for the AP mesh the SON again?
8. After multiple APs are detected by searching and pairing on the SON, how do I check how these APs are connected?
9. What factors does the Master AP consider when doing the link optimization?
10. What is the recommended number of the mesh accesses?
11. Why is a maximum of three hops recommended for establishing the mesh SON?
12. If a Root AP establishes the mesh with 4 downlink Reyee APs, How to allocate the bandwidth of these 4 downlink APs?
13. If the SON function is disabled, can the RAP in the network still support mesh?
14. If the EG works as the AC mode, can it do the SON establishment? And can it support mesh?
15. Does the Reyee AP mesh can designate the next hop?
16. Will the Reyee AP mesh affect the roaming experience of terminals? In a mesh SON, why does the rate will decrease after the STA roaming?
17. Can RAP do mesh with the devices of other brands?
18. Can RAP connect the devices of other brands by wireless repeater?
19. Can RAP do mesh with the EW series products?
20. What will RAP do if the uplink device fails during the process of mesh?
21. When the RAP SON do mesh, must the RAP be the master?
22. Can two RAPs that support mesh connect by the wireless repeater?
23. What’s the distance limitation when RAPs do the mesh?
24. What pairing methods does AP Mesh support?
25. How to configure Reyee AP mesh ?
RG-RAP6260(G)

FAQ Mesh function Wireless
There are no replies.
Related Posts
Product Model

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2023 Ruijie Networks Co,Ltd