dynamic VLAN assignment on ruijie cloud

hi everyone. i did all of my other config for 802.1x. i just need to add more than one vlan id to my same ssid. how can i do it?

Dear sir,

If you have Ruijie Enterprise APs, you may refer to the following link for the commands to configure dynamic vlan: https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=2888&extra=page%3D1


Best regards

Jayden

GTAC-Jayden replied at 2023-2-27 10:16
Dear sir,

If you have Ruijie Enterprise APs, you may refer to the following link for the commands t ...

i did it. when i did it my whole config deleted. for example; i want to set up to my one ssid ten VLAN. 10,20,30 IDs vs vs. is there any video of this

adotelli replied at 2023-2-27 16:25
i did it. when i did it my whole config deleted. for example; i want to set up to my one ssid ten  ...

Dear adotelli,

May I please know if you saved everything at the end by typing:
Ruijie(config)#end
Ruijie#wr

Best regards,
Jayden

GTAC-Jayden replied at 2023-2-27 17:19
Dear adotelli,

May I please know if you saved everything at the end by typing:

Dear Jayden;
Thank you so much for your quick respond. when i did all config, what will i write for vlan ID or what should i do ruijiecloud side.

adotelli replied at 2023-2-27 18:15
Dear Jayden;
Thank you so much for your quick respond. when i did all config, what will i write f ...

Dear adotelli,

You may enter the commands on cloud Web CLI, so that the configuration will not be affected by cloud synchronization.

Best regards,
Jayden

GTAC-Jayden replied at 2023-2-27 18:25
Dear adotelli,

You may enter the commands on cloud Web CLI, so that the configuration will not be ...

it worked. thank you so much jayden for your help. you are the best <3

best regards

adotelli replied at 2023-2-27 20:36
it worked. thank you so much jayden for your help. you are the best

hi again jayden. may i ask one more help? like i said it worked. but i tried whole scenario with one AP which is 820 v3. if i add new APs to my wireless network. what should i do? should i do same thing to new aps if it is so, all aps will be meshed? i mean roaming will be active?

adotelli replied at 2023-2-28 16:39
hi again jayden. may i ask one more help? like i said it worked. but i tried whole scenario with o ...

Dear adotelli,



If you have multiple APs, you may refer to this post on how to batch configure CLI commands:

https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=2007


Once you finish the configuration, all APs should have the same vlan-group and thus they will all have the same VLANs, Layer 2 roaming will be active since intra-VLAN roaming will take place. Please kindly note that Layer 2 roaming is enabled by default.


Best regards,

Jayden

GTAC-Jayden replied at 2023-3-1 13:09
Dear adotelli,

hi again jayden;
when i try to this config i can't see any device. in my project i have only access points (820 v3). there is no acess controller or gateway.

adotelli replied at 2023-3-1 16:34
hi again jayden;
when i try to this config i can't see any device. in my project i have only acces ...

Dear adotelli,

Please kindly refer to this post:
https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=1760&extra=page%3D1


Sorry for the mistake.

Best regards,
Jayden