Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The category of your feedback

Your Feedback

Your Email address (optional):

Network Printer Issues Reply

Carol Anderson

Level 1

Network Printer Issues
1423 11 2024-8-3 19:39:58
Original
I have a new printer which I was trying to install on the network. I could not get the Brother software to find the printer.

I tried many things and almost went to send the printer back. I can see it connected to my SSID (GSPSTAFFNET) in the cloud (see image below) however when I tried to access it via the IP 192.168.1.35  it says that the address is unreachable.

As I am about to post the printer back to return it I decided to try it directly connected to the router wifi and not via Ruiiji AP's. I connected it to an SSID I have directly coming off my router directly and the IP was immediately accessible. I need this printer on GSPSTAFFNET so can you tell how to make the IP reachable on via this SSID please.




Ruijie Cloud

Cloud Wireless Ruijie Cloud
0 2024-8-5 10:26:18 View all replies
Hi, Carol Anderson

If the printer and users are connected to the same SSID but cannot access each other, please check if you have enabled client isolation on the SSID. If so, please disable the Client Isolation.



Best regards,
Jayden

0 2024-9-25 16:00:05 View all replies
GTAC-Jayden replied at 2024-8-5 10:26
Hi, Carol Anderson

If the printer and users are connected to the same SSID but cannot access each o ...

I have the same issue. I have tried several configuration but not able to solve this issue.

0 2024-10-25 19:49:33 View all replies
Milan replied at 2024-9-25 16:00
I have the same issue. I have tried several configuration but not able to solve this issue.

We have a similar issue, the printer cannot print and this we noticed after the firmware upgrade on the reyee gateway, however we are connected via network cable and not ssid. The printer company said we need to roll back the firmware on the gateway or try a different router. We could not roll back the firmware, but we did try a different router and the printer works fine on the other router.
Do you have any solutions to fix this printing issue?
BTW: it is an HP multi function printer
Many Thanks
Devan

0 2024-10-25 20:44:38 View all replies
Devan Moodley replied at 2024-10-25 19:49
We have a similar issue, the printer cannot print and this we noticed after the firmware upgrade o ...

Dear Devan,

Could you please show your model and configuration of your router?

Or you can directly come to reach us via RITA.
You can enter this url https://www.ruijienetworks.com/support,

check right bottom corner, choose"Contact us" -> "Online Support"

Best Regards,
William

0 2024-10-25 21:06:13 View all replies
GTAC-Jayden replied at 2024-8-5 10:26
Hi, Carol Anderson

If the printer and users are connected to the same SSID but cannot access each o ...

Client isolation is not turned on. My model is Brother_DCP_L3560CDW_series.

I have had to locate my printer next door where my router is located as I still cannot connect via my SSID and AP's.


0 2024-10-25 23:33:54 View all replies
Carol Anderson replied at 2024-10-25 21:06
Client isolation is not turned on. My model is Brother_DCP_L3560CDW_series.

I have had to locate ...

Hi sir
We attach great importance to your current problem. In order to contact you better and in a timely manner. Can you access our online support platform www.ruijienetworks.com/rita , we can check together.
Best Regards
Tom

0 2024-10-26 02:47:32 View all replies
Hi, Carol!
I had a similar issue. So i tried to set a static IP on the printer i made it by the "eWeb" interface on the EG (i have an EG105G-V2) device, in the LAN option. Then i made a test and it works! So i hope to been helpfully!

0 2024-11-1 11:56:04 View all replies
Devan Moodley replied at 2024-10-25 19:49
We have a similar issue, the printer cannot print and this we noticed after the firmware upgrade o ...

We have received your question and our team is checking it. We will provide you with a solution via email later.

0 2024-11-4 21:40:46 View all replies
Devan Moodley replied at 2024-10-25 19:49
We have a similar issue, the printer cannot print and this we noticed after the firmware upgrade o ...

also in my case after downgrade of the fw of the gatewai from OS 300 to OS 280 the problem was solved.
Please investigate with R&D
Marco

0 2024-11-4 22:11:46 View all replies
Mturco84 replied at 2024-11-4 21:40
also in my case after downgrade of the fw of the gatewai from OS 300 to OS 280 the problem was sol ...

Hi sir,

After confirmed with R&D, I will reply you asap.

Best regrads,
Steve

0 2024-11-6 23:53:41 View all replies
So I finally gave in and wired the printer in to the network and it works. Kind of annoying because I had hope to avoid more wires but at least it works and is reliable.

Related Posts
Product Model

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2023 Ruijie Networks Co,Ltd