1.1 RG-WALL 1600-Z3200-S Panels
1.1.1 Front Panel
Front Panel
Components on the Front Panel
No.
Component
Description
1
SATA hard disk status LED (SATA)
Steady green: A hard disk is connected.
Blinking green: Data is being read or written.
2
Power module status LED (PWR)
Steady green: The power supply is normal.
Off: The power supply is cut off or fails.
3
System status LED (SYS)
Blinking green: The device is powered on and being initialized.
Steady green: Initialization is complete.
Steady red: An alarm is generated.
4
Reset button
Restarting the device: Press the button for less than 3 seconds.
Restoring factory settings: Press the button for more than 5 seconds. When you perform either of the preceding operations, device status information is collected. After the device restarts, you can access the web UI of the firewall, choose O&M >
Fault Diagnosis >
One-Click Collection, and download the information.
5
Console port
It is used to connect to the console for device maintenance and diagnosis.
Note:
When the console port is used, set the baud rate to 115,200 bps, data bit to 8, and stop bit to 1, and disable parity check and data flow control.
The console port is used only in special scenarios. For details, contact technical support personnel.
6
USB port
Two USB 2.0 ports can be used to connect USB drives.
7
MGMT port
It is used to access the device management page upon first login.
8
10/100/1000BASE-T ports
Ports 1 to 7, which are used to connect Ethernet cables.
9
10GE SFP + port LED
Steady green: The port is connected.
Blinking green: The port is receiving or sending data.
Off: The optical port is incorrectly connected.
10
1GE SFP port LED
Steady green: The port is connected.
Blinking green: The port is receiving or sending data.
Off: The optical port is incorrectly connected.
11
1GE SFP port
Port 8F. For details about optical modules that support this port
12
10GE SFP+ port
Port 0F. For details about optical modules that support this port
13
Link/ACT status LEDs (square) of 10/100/1000BASE-T ports
Steady green: The port is connected.
Blinking green: The port is receiving or sending data.
Off: The port is incorrectly connected.
14
Speed LEDs (round) of 10/100/1000BASE-T ports
Steady orange: Gbit/s port speed
Off: 100/10 Mbit/s port speed
1.1.2 Rear Panel
Rear Panel
Components on the Rear Panel
No.
Component
Description
1
Installation position of a power cord retention clip
Used to install a power cord retention clip.
2
Power socket
Used to connect an AC power cord.
3
Power switch
Used to power on or power off the device.
4
Expansion slot for a hard disk
Used to install a hard disk.
5
Grounding terminal
Used to ground the device to ensure electrical safety.
1.2 RG-WALL 1600-Z5100-S Panels
1.2.1 Front Panel
Front Panel
Components on the Front Panel
No.
Component
Description
1
MGMT port
It is used to access the device management page upon first login.
2
System status LED (SYS)
Blinking green: The device is powered on and being initialized, or the system is restoring factory settings.
Solid green: Initialization is complete.
Solid red: An alarm is generated.
3
Power module status LEDs (PWR0 and
Solid green: The power module is operating normally.
Solid red: The power module is not functioning properly, or the power module is installed but no power cord is connected.
Off: No power supply is connected.
4
SATA hard disk status LED (SATA)
Solid green: A hard disk is connected.
Blinking green: Data is being read or written.
5
Reset button
Restarting the device: Press the button for less than 5 seconds.
Restoring factory settings: Press the button for more than 5 seconds. When you perform either of the preceding operations, device status information is collected. After the device starts, you can log in to the web UI of the firewall, choose O&M >
Fault Diagnosis > One-Click Collection, and download device status information.
6
Console port
It is used to connect to the console for maintenance and diagnosis. Note:
When the console port is used, set the baud rate to 115,200 bps, data bit to 8, and stop bit to 1, and disable parity check and data flow control.
The console port is used only in special scenarios. For details, contact technical support personnel.
7
USB port
Two USB 2.0 ports can be used to connect USB flash drives.
8
Link/ACT status LEDs (square) of 10/100/1000BASE-T ports
Solid green: The link on the port is Up.
Blinking green: The port is receiving or sending data.
Off: No link is established on the port.
9
Speed LEDs (round) of 10/100/1000BASE-T ports
Solid orange: Gbps port speed
Off: 100/10 Mbps port speed
10
10/100/1000BASE-T ports
Ports 1 to 7, which are used to connect Ethernet cables.
11
1GE SFP port LEDs
Solid green: The port is connected.
Blinking green: The port is receiving or sending data.
12
10GE SFP + port LEDs
Solid green: The port is connected.
Blinking green: The port is receiving or sending data.
13
10GE SFP+ ports
Ports 0F to 3F
14
1GE SFP ports
Ports 8F and 9F
15
Module slots
Expansion module slots
Rear Panel
Components on the Rear Panel
No.
Item
Description
1
Grounding terminal
Used to ground the device to ensure electrical safety.
2
Hard disk slot
Used to install a hard disk.
3
Powerswitch
Used to power on or power off the device.
4
Power module
Used to connect an AC power cord. Two power modules can be installed.
This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.
Level 6
