How to configure static route on Ruijie device?

Introduction
Static routes are manually configured so that the packets can be sent to the specified destination network go through the specified route.  Static routes can be very important if the switch don't support dynamic routing protocol(RIP,OSPF etc.) and are useful for specifying a gateway of last resort to which all unroutable packets are sent.

Case of configuration
a) Requirement
Configure the switch with static routes and ensure that users in network 1 can communicate with users in network 2

b) Network Topology


c) Configuration Tips
1) Assign IP addresses to SW1 and SW2
2) Configure Static Routes on SW1
3) Configure Static Routes on SW2
4) Save Configuration

d) Configuration Steps  
1) Assign IP address to SW1

Ruijie>enable               

Ruijie#configure terminal   

Ruijie(config)#interface fastethernet 0/1

Ruijie(config-if-FastEthernet 0/1)#no switchport

Ruijie(config-if-FastEthernet 0/1)#ip address 192.168.1.254 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)#interface GigabitEthernet 0/25

Ruijie(config-if-GigabitEthernet 0/25)#no switchport

Ruijie(config-if-GigabitEthernet 0/25)#ip address 192.168.3.1 255.255.255.0

Ruijie(config-if-GigabitEthernet 0/25)#exit

2) Assign IP address to SW2

Ruijie>enable               

Ruijie#configure terminal   

Ruijie(config)#interface fastethernet 0/1

Ruijie(config-if-FastEthernet 0/1)#no switchport

Ruijie(config-if-FastEthernet 0/1)#ip address 192.168.2.254 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)#interface GigabitEthernet 0/25

Ruijie(config-if-GigabitEthernet 0/25)#no switchport

Ruijie(config-if-GigabitEthernet 0/25)#ip address 192.168.3.2 255.255.255.0

Ruijie(config-if-GigabitEthernet 0/25)#exit

3) Configure Static Routes on SW1

Ruijie(config)#ip route 192.168.2.0 255.255.255.0 192.168.3.2  //configure static routes to destination subnet 192.168.2.0/24 and next hop is 192.168.3.2

Note：
1) When you configure static routes, there're two ways to specify next hop. You can specify an IP address ,or you can specify a local outgoing interface.
2) We suggest you to use IP address as next hop
4) Configure Static Routes on SW2

Ruijie(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1  //configure static routes to destination subnet 192.168.1.0/24 and next hop is 192.168.3.1

5) Save configuration

Ruijie(config)#end         

Ruijie#write

Verification
You can use "ping" on a station in network 1 to verify network connectivity
"run"-->"cmd"-->"ping x.x.x.x" (x.x.x.x is a host in network 2)
How to display ip routing table

Ruijie#show ip route

Codes:  C - connected, S - static, R - RIP, B - BGP
        O - OSPF, IA - OSPF inter area
        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
        E1 - OSPF external type 1, E2 - OSPF external type 2
        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
        ia - IS-IS inter area, * - candidate default
Gateway of last resort is no set
S    192.168.2.0/24 [1/0] via 192.168.3.2
C    192.168.3.0/24 is directly connected, GigabitEthernet 0/25
C    192.168.3.1/32 is local host.
C    192.168.1.0/24 is directly connected, FastEthernet 0/1
C    192.168.1.254/32 is local host.