How to enable MDNS protocol ?
|
Edited by unknown unknown at 2023-10-6 22:22 1. IPTV Vlan 130 (10.9.130.100 IPTV Server IP) 2.Chromecast Vlan 190 (10.9.190.x IP of any Chromecast device) 3.Guest Vlan 170 (IP of 10.9.170.x Guest phones) Ouraim is to ensure that phone and tablet devices connected to the Guest Vlan(Vlan 170) can transmit images to the Chromecast Vlan (Vlan 190) under thesupervision of IPTV Vlan 130. For this reason, it is desired that no protocolblocks data transfer between vlans. Studies have observed that there areobstacles in the transfer between vlans. It is thought that the problem can besolved by enabling the MDNS protocol. Therelevant 3.16.4.1 Enabling the Bonjour Gateway page of the Ruijie RG-WLANImplementation Cookbook (V4.1) of my request in question shows a similartopology. However, when I want to apply this recommended method, the switchdefines the commands incorrectly.   |
|
https://www.ruijienetworks.com/support/documents/slide_75752#_1.4.2_Configuring_Bonjour Unfortunately, the methods here do not work. |
|
Dear Sir/Madam Bonjour protocol can be enabled on Ruijie gateway products, it may not be available on S2910-10GT2SFP-P-E currently. |
User 18152 replied at 2023-10-6 23:22 Hello Davit, First of all, thank you for responding to my topic. I thought I read in the above cookbook (Ruijie RG-WLAN Implementation Cookbook (V4.1)) that this can be done on the switch. Please correct me if I'm wrong. I leave the link below https://www.ruijienetworks.com/support/documents/slide_75752#top |
Emrah Güler replied at 2023-10-11 22:02 Dear Emrah Güler, Please kindly note the Bonjour Gateway configuration is applicable to the Access Controller (RG-WS series). Your topology does not show an AC in the network, may I please know if the APs are running in fat or macc mode? Please try the following commands to allow mDNS broadcast forwarding on the APs? Ruijie(config)#data-plane close-mdns-filter enable Best regards, Jayden |
GTAC-Jayden replied at 2023-10-11 22:15 Jayden, I stated it as Ap180 in the topology, I think you will see it if you check it again. All Access points work in macc mode. |
GTAC-Jayden replied at 2023-10-11 22:15  Jayden Thank you, I applied the code you recommended to the AP. it was accepted, but shouldn't we write something in the switch section? |
GTAC-Jayden replied at 2023-10-11 22:15 Hello again, This simple detail escaped my attention. Can you help me on how to apply the recommendations in the book to my own system? There are 46 customer rooms and each room has 2 TVs, 1 Ap 180. Incoming customers want to watch broadcasts on TV by sharing the screen from their phones. |
This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.
More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.
©2000-2023 Ruijie Networks Co,Ltd
Level 1
