Forgot password?
 Register now

Welcome to use this form to feedback your problems with Ruijie Community

The category of your feedback

Your Feedback

Your Email address (optional):

cant config wan0 + wan1 with wifi employee + guest Reply

Issa Yaser

Level 1

cant config wan0 + wan1 with wifi employee + guest
3198 17 2023-2-6 22:18:55
Original
Edited by Issa Yaser at 2023-2-6 22:31

i have project  with EG210G-p  + RAP2260 ( 12 unit )
i config 2 wifi    employye / guest ...  the guest wifi should use internet from wan1 only

anybody do this before  . i try many things but i guess ist not possible .
RG-EG210G-P

Router
0 2023-2-7 16:21:53 View all replies
Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configure Load Balance



2.Configure ACL: Block Guest IP address pass through WAN0




0 2023-2-10 01:03:53 View all replies
Toby1 replied at 2023-2-7 16:21
Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configur ...

hi bro thanks for your reply .
but it doesn't work. still the guest Wi-Fi can access the internet throw wan-0

simply. the need is  
Wi-Fi employee use only wan-0
Wi-Fi guest use only wan-1
no balance or fail over need.

my network config ,
Wi-Fi emp ip(192.168.22.1)vlan defult  / wan-0  ip (192.168.3.11)
Wi-Fi guest ip (192.168.33.1)vlan33 / wan-1 ip (192.168.5.13)

0 2023-2-10 12:26:56 View all replies
Issa Yaser replied at 2023-2-10 01:03
hi bro thanks for your reply .
but it doesn't work. still the guest Wi-Fi can access the internet  ...

Bro, could you try the following configuration?









0 2023-2-13 02:11:17 View all replies
Toby1 replied at 2023-2-10 12:26
Bro, could you try the following configuration?

bro
the same doesn't work. still Wi-Fi guest can access internet throw another wan .
i reset all the project and reconfigure all devices. but same result


i think this device can't be secure on network. and can't divided wan's

0 2023-2-13 09:22:06 View all replies
Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access internet throw another wan .
i reset all  ...
Hi, bro.
Could you refer this link to do a configuration :https://www.ruijienetworks.com/resources/preview/77309
On the page 65.

0 2023-2-13 21:58:01 View all replies
Toby1 replied at 2023-2-7 16:21
Hi bro,
You can configure load balancing on EG, and then configure ACL to filter traffic.
1.Configur ...

How can I find more informations?


0 2023-2-16 06:02:04 View all replies
Steve replied at 2023-2-13 09:22
Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access inter ...

hi bro

i do everything. but same result still doesn't work.

0 2023-2-16 06:04:41 View all replies
Steve replied at 2023-2-13 09:22
Issa Yaser replied at 2023-2-13 02:11
bro
the same doesn't work. still Wi-Fi guest can access inter ...

dear
i do everything. step by step .
but doesn't work. the Wi-Fi network still can access both wans.

0 2023-2-16 09:08:02 View all replies
Issa Yaser replied at 2023-2-16 06:04
dear
i do everything. step by step .
but doesn't work. the Wi-Fi network still can access both w ...

Hi bro,
Could you please share your network with me? This is my email:liuxiyang@ruijie.com.cn

0 2023-11-14 07:20:40 View all replies
GTAC-Steve replied at 2023-2-16 09:08
Hi bro,
Could you please share your network with me? This is my email:liuxiyang@ruijie.com.cn

Hi I have the same issue but cannot find how to get this working. Can i get some assistance.
I have 2 vlans:    VLAN2 for guest 192.168.2.1-254 and VLAN 1 for admin 192.168.1.1-254. both have their own SSID's

I want Vlan1 to use WAN0 and WAN 1 as fail over, and VLAN2 use WAN2
i cannot figure it out

0 2023-11-21 02:51:55 View all replies
Dear All,
Good day to you ! are you able to overcome this issue ! I would like to configure the same setting on my customer side using EG305GH-P-E which using 2 difference ISP provider. Hopefully you able to overcome this issue

Thank you


0 2023-11-21 14:34:27 View all replies
User 58099 replied at 2023-11-21 02:51
Dear All,
Good day to you ! are you able to overcome this issue ! I would like to configure the sam ...

Hi sir,

please kindly refer to this link to configure it :https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=5720


Best regards,
Steve

0 2023-11-22 23:27:48 View all replies
GTAC-Steve replied at 2023-11-21 14:34
Hi sir,

please kindly refer to this link to configure it :https://community.ruijienetworks.com/fo ...

Dear Steve,
thank you for your reply ! but what I means is certain ip address to redirect to Wan 2 of the Another ISP provider instead using load
balancing on  RG-EG305GH-P-E , which about the same question of the  user
cant config wan0 + wan1 with wifi employee + guest
1195122023-2-6 22:18:55

asking about !  any idea to configure it

thank you

0 2023-11-23 08:59:45 View all replies
User 58099 replied at 2023-11-22 23:27
Dear Steve,
thank you for your reply ! but what I means is certain ip address to redirect to Wan  ...

Dear:

Have you tried to deploy this config but using PBR on your reyee EG?

If not, please refer to the following link:

https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=4010

The scenario presented shows how to reach internet only
using one ISP.

Regards,

Javier

0 2023-11-24 02:22:49 View all replies
GTAC--Javier replied at 2023-11-23 08:59
Dear:

Have you tried to deploy this config but using PBR on your reyee EG?

Dear Javier ,
will try on PBR on your reyee EG way to do it . thank you

But  If my customer having 3 Wan ISP link , how do I configure it , using the following link above way to configure PBR to route WAN 3?


Thank you

0 2023-11-24 08:05:16 View all replies
User 58099 replied at 2023-11-24 02:22
Dear Javier ,
will try on PBR on your reyee EG way to do it . thank you

Dear:

Sorry, I think I was not clear enough. The link that I shared with you explains how to forward traffic through only one WAN interface when you are currently using 2 or more egress interfaces (which would be multi-WAN scenario, just like in your project). So, you can follow the steps as explained in the link

Regards,

Javier

0 2023-11-24 12:41:01 View all replies
GTAC--Javier replied at 2023-11-24 08:05
Dear:

Sorry, I think I was not clear enough. The link that I shared with you explains how to forw ...

Dear Javier,
  Thank you for your email. you not clear my question sometime.. that why I prefer draw a diagram to you, As well I also not clear your explain to me sometime .sorry .. anyway thank you for your help to answer my question . So ,you answer my the question " you can follow the steps as explained in the link"

you means this link https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=4010?

thank you

Related Posts
Product Model

Share this topic to

Cancel

This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.

More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.

©2000-2023 Ruijie Networks Co,Ltd