Model: AP720-L
|
How to configure the Trunk port at this AP 720L which allow multi VLAN pass |
|
Hi Aimin Then Please kindly refer to this guide to configure it. How to configure trunk port on Ruijie device? - Switch - Ruijie Community (ruijienetworks.com) |
GTAC-Vivian replied at 2024-4-12 11:04 HI, It show as unknow command Ruijie#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Ruijie(config)#interface gigabitEthernet 0/1 Ruijie(config-if-GigabitEthernet 0/1)#switchport mode trunk % Unknown command. |
Aimin Then replied at 2024-4-12 11:22 Dear Aimin Then, Please kindly refer to this guide to configure it. We need to encapsulate vlan id in sub interface. Ruijie(config)#int g0/1.1 Ruijie(config-subif-GigabitEthernet 0/1.1)#encapsulation dot1Q 20 Please try this method. If the issue is still exist after, please help to collect the result and talk with me again. I would be glad to help you in Community. |
GTAC-Vivian replied at 2024-4-12 14:35 HI Still same Ruijie#int g0/1.1 % Unknown command. Ruijie#int g0/1.1 % Unknown command. Ruijie# |
GTAC-Vivian replied at 2024-4-12 14:35 HI Still same Ruijie#int g0/1.1 % Unknown command. Ruijie#int g0/1.1 % Unknown command. Ruijie# |
GTAC-Vivian replied at 2024-4-12 14:35 Hi , Still error Ruijie#int g0/1.1 % Unknown command. Ruijie#int g0/1.1 % Unknown command. Ruijie# |
GTAC-Vivian replied at 2024-4-12 14:35 Hi , Still error Ruijie#int g0/1.1 % Unknown command. Ruijie#int g0/1.1 % Unknown command. |
Aimin Then replied at 2024-4-12 15:05 Dear Aimin Then, Please kindly add one command at the first, then input other commands like this: Ruijie#configure terminal Ruijie(config)#int g0/1.1 Ruijie(config-subif-GigabitEthernet 0/1.1)#encapsulation dot1Q 20 This is an example, you could change the parameter as your plan. If the issue is still exist after, please help to collect the result and talk with me again. I would be glad to help you in Community. |
GTAC-Vivian replied at 2024-4-12 15:07 Hi, i managed to add it but i cant connnect to the internet using the new Vlan 32 which i just created |
Aimin Then replied at 2024-4-12 15:16Dear Aimin Then, I‘m sorry that we can't provide a specific solution for you based on current information. Can you help to check the follows aspects： 1. Check if you can get ip address or you can get ip address but cannot get internet. If you cannot get ip address, please check if you have configured dhcp settings on the server and then if you have created and allow these vlan on the rest devices, like switches and APs. 2. If you can get ip address but cannot get internet, please check if you have created and allow these vlan on the rest devices, like switches and APs. If the issue is still exist, please help to collect the result and talk with me again. I would be glad to help you in Community. |
This site contains user submitted content, comments and opinions and is for informational purposes only. Ruijie may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic forum and Ruijie can therefore provide no guarantee as to the efficacy of any proposed solutions on the community forums. Ruijie disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. All postings and use of the content on this site are subject to the Ruijie Community Terms of Use.
More ways to get help: Visit Support Videos, call us via Service Hotline, Facebook or Live Chat.
©2000-2023 Ruijie Networks Co,Ltd
Level 1
